Sharp MX-4110N Installation Manual

Also see for MX-4110N: Operation manual Operation guide

Contents

MX-5111N IC card reader 32 – 8(2) Setting of the HID setting fileFor [Decoding\CardId] section, the same as above.When Data = #!abcde$12345%vxxyz ;Example 1: Specification by positionPosition = 3Length = 5Decoded Data = abcdeExample 2: Specification by delimiterStart.Delimiter = $End.Delimiter = %Decoded Data = 12345When Decoded Data = 12345 ;ExamplePre = #%Post = abcPadded Data = #%12345abcD. Card reading testAfter importing the user area setting to the machine, a test can beexecuted to confirm that the cars is properly read. (* User control >Card area setting > Card reading test (* Only the system settings ofthe machine))Execute "User control > Card area setting > Card scan test"The result displays after completion of a test are described below.(When reading is successfully completed, the content of data readfrom the card is displayed. When reading is failed, an error displayis made.)(1) Error displays in case of a reading failure(2) Display when card reading is successfullycompletedRead Success.Card ID: XXXXXXFacility Code: XXXXXX* When card reading is successfully completed, the result is indi-cated as shown above with the user information. Check to con-firm that the displayed items are proper. If not, check theimproper item.HID setting file templateThe extension of “ini” should be added.Section name DescriptionDecoding\FacilityCodeDecode setting of the facility code.(* If the facility code is not used, there is no need todescribe this item.)Decoding\CardId Decode setting of the card ID.(* If the card ID is not decoded and all the read dataare used for the card ID, there is no need to describethis item.)[ Decoding\FacilityCode]Key name DescriptionLocation Location specifying methodByPosition: Specifying by positionByDelimiter: Specifying by delimiter* If the facility code has no setting of this item, it isNULL.* If the card ID has no setting of this item, all the dataread from the card is made the card ID.Position Start position (1 - 128) is specified with a decimalnumber.(* Specified only when the location key value is"ByPosition".)* The head is specified with 1 and later.Length Position The length of reading from the position specified withthe key is specified with a decimal number (1 - 128).(* Specified only when the location key value is"ByPosition".)* The total of this set value and the value specifiedwith Position key must be 128+1 or less.Start.Delimiter Delimiter (Front)(* Specified only when the location key value is"ByDelimiter".)* Only ASCII code printable characters can be usedfor specification.End.Delimiter Delimiter (Back)(* Specified only when the location key value is"ByDelimiter".)* Only ASCII code printable characters can be usedfor specification.Section name DescriptionPadding\CardId Card ID padding setting[Padding\Data]Key name DescriptionPre Front padding (Max. 3 characters)* Only ASCII code printable characters can be usedfor specification.Post Back padding (Max. 3 characters)* Only ASCII code printable characters can be usedfor specification.Details of errorError display Error content and remedyCard is notfound.Content Card is not found.Remedy Check to confirm that the card is securely setin the card reader.Read Error. Content A read error occurs.Remedy Check to confirm that the card and cardreader operate normally with a personalcomputer, etc.hid_template E;; HID setting file# General information setting[General]Version=1.0Card=HID# Decode setting of the facility code[Decoding\FacilityCode]Location=ByPositionPosition=1Length=8# Decode setting of the card ID[Decoding\CardId]Location=ByDelimiterStart.Delimiter=!End.Delimiter=?# Card ID padding setting[Padding\CardId]Pre=@@@Post=\\\: '11/Jul/251