Sealey STW292.V2 Quick Start Manual

torque adaptor digital 3/4” sq. drive200-1000nm (147.5 - 737.5lb.ft)MODEL NO: stW292.v2thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.important: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. safetY Warning! do not use the digital torque adaptor if damaged or thought to be faulty.8 do not apply force to the digital torque adaptor when the power is off. Always turn it on before using it, otherwise it will be damaged.8 do not turn off the digital torque adaptor while torque force is being applied to it.8 do not exceed the permitted maximum torque value. To do so will cause it to break.8 do not subject the 3/4” connectors to any force other than a rotational one.9 Ensure that all components including all adaptors, extensions, drivers and sockets are rated to match or exceed the torque beingapplied.9 Observe all equipment, system and manufacturer’s warnings, cautions and procedures when using this digital torque adaptor.9 Use the correct size socket for the fixing.8 do not use sockets that are worn or cracked.9 Check that the digital torque adaptor capacity matches or exceeds each application before proceeding.9 Ensure all workshop safety rules, regulations, and conditions are complied with when using this digital torque adaptor.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the working area.8 do not press, pressure, or damage the LCD display.8 do not use near strong magnetic fields.8 do not subject to excessive force or shocks.8 do not drop or throw the digital torque adaptor.8 do not leave the digital torque adaptor in any place exposed to excessive heat, humidity or direct sunlight.8 do not use organic solvents such as alcohol or thinners for cleaning.8 do not submerge in water or any other liquid.8 do not disassemble the digital torque adaptor.9 To ensure accurate measurement, periodic re-calibration is necessary.9 After use, clean with a soft dry cloth and store in a safe, dry, childproof location away from any heat sources.9 Avoid any dusty, damp or humid conditions.2. introductionDesigned for use with a standard ratchet or breaker bar. Ideal for work around the engine bay and the tightening of wheel nuts to factoryspecifications. Large LCD display with LED/audible alarm indicating achieved and target torque levels. Selectable readings in Nm, lb.ft orkg.m and accurate to ±2% of stated capacity. Memory stores up to 50 readings and features auto shut off after 70 seconds. Suppliedwith test certificate and storage case.3. specificationModel no .............................................................STW292.V2Range ................................... 200-1000Nm (147.5-737.5lb.ft)Accuracy .........................................................................±2%Resolution ......................................................................... 0.1Drive .......................................................................... 3/4”sq.Units .................................................................. Nm/lb.ft/kg.mSize (L x W)...................................................110mm x 56mmWeight ......................................................................... 0.72kgOperating modes............................................ trace and peakMemory space.................................................................... 50Battery ................................................................. 2 x AA typeBattery life ......................................................up to 110 hoursOperating temp ............................ -10°C~60°C/13.9~139.9°FStorage temp ................................... -20°C~70°C/-4~157.9°FRefer toinstructionmanualWear eyeprotectionOriginal Language Version© Jack Sealey Limited STW292.V2| Issue:1 20/08/18

/ 3

Related manuals for Sealey STW292.V2