Sealey STW292 Instructions Manual

INSTRUCTIONS FOR:DIGITAL TORQUE ADAPTOR3/4” Sq. Drive - 100 - 500NmMODEL No: STW292IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGSAND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURETO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEPINSTRUCTIONS SAFE FOR FUTURE USE.Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to theseinstructions and properly maintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONS 3. SPECIFICATION2. INTRODUCTION4. OPERATIONDesigned for use with a standard ratchet or breaker bar. Idealfor work around the engine bay and the tightening of wheelnuts to factory specifications. Large LCD display with LED/audible alarm indicating achieved and target torque levels.Selectable readings in Nm, lb.ft or kg.m and accurate to ±2%of stated capacity. Memory stores up to 50 readings andfeatures auto shut off after 80 seconds. Supplied with testcertificate and storage case.STW292 Issue No.1 26/07/12Original Language Version© Jack Sealey LimitedNOTE: DO NOT press the Mem and Power buttons at thesame time as this will enter calibration mode.4.1. Preparation.4.1.1. Unscrew the four cross-head screws holding the rearbattery cover and remove the battery cover (fig.1).Install two AA batteries, ensuring correct polarity. Refitthe battery cover and refit and tighten the fourcross-head screws.NOTE: When battery power is low, a low battery icon will bedisplayed.NOTE: DO NOT use the digital torque adaptor when thebattery is in a low state of charge as this will affect thetorque adaptor’s accuracy. WARNING! DO NOT use the digital torque adaptor ifdamaged or thought to be faulty. DO NOT apply force to the digital torque adaptor whenthe power is off. Always turn it on before using it,otherwise it will be damaged. DO NOT turn off the digital torque adaptor while torqueforce is being applied to it. DO NOT exceed the permitted maximum torque value.To do so will cause it to break. DO NOT subject the 3/4” connectors to any force otherthan a rotational one. Ensure that all components including all adaptors,extensions, drivers and sockets are rated to match orexceed the torque being applied. Observe all equipment, system and manufacturer’swarnings, cautions and procedures when using thisdigital torque adaptor. Use the correct size socket for the fixing. DO NOT use sockets that are worn or cracked. Check that the digital torque adaptor capacity matches orexceeds each application before proceeding. Ensure all workshop safety rules, regulations, andconditions are complied with when using this digitaltorque adaptor. Maintain correct balance and footing. Ensure the floor isnot slippery and wear non-slip shoes. Keep children and unauthorised persons away from theworking area. DO NOT press, pressure, or damage the LCD display. DO NOT use near strong magnetic fields. DO NOT subject to excessive force or shocks. DO NOT drop or throw the digital torque adaptor. DO NOT leave the digital torque adaptor in any placeexposed to excessive heat, humidity or direct sunlight. DO NOT use organic solvents such as alcohol orthinners for cleaning. DO NOT submerge in water or any other liquid. DO NOT disassemble the digital torque adaptor. To ensure accurate measurement, periodic re-calibrationis necessary. After use, clean with a soft dry cloth and store in a safe,dry, childproof location away from any heat sources.Avoid any dusty, damp or humid conditions.MODEL: STW292Range: 100-500Nm/73.8-369lb.ft/10.19-50.98kg.mAccuracy: ±2%Resolution: 0.1Drive: 3/4” Sq. DriveUnits: Nm/lb.ft/kg.mSize (L x W): 110mm x 56mmWeight: 570gOperating Modes: Trace & PeakMemory Space: 50Battery: 2 x AA TypeBattery Life: Up to 110 HoursOperating temp: -10 ~ 60ºC/13.9 ~ 139.9ºFStorage temp: -20 ~ 70ºC/-4 ~ 157.9ºFHumidity: 15 ~ 90% Non-condensingfig.1

/ 2

Related manuals for Sealey STW292