Sealey AK9636D Instructions Manual

INSTRUCTIONS FORELECTRONIC DIGITAL HEIGHT GAUGEModel No: AK9636DThank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.IMPORTANTPLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, ANDCAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TODO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.pp WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools and equipment.7 DO NOT use the gauge if damaged.3 Maintain the gauge in good and clean condition for best and safest performance.3 Keep the work area clean, uncluttered and ensure there is adequate lighting.3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.3 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellry. Contain or tie back long hair.3 Keep children and unauthorised persons away from the work area.1. SAFETY INSTRUCTIONS2. INTRODUCTION & SPECIFICATIONPrecision ground base with 6 button electronic gauge. Includes fine adjustment control carriage for accurate use. 6-Digit LCD read-out displays in metric orimperial. Features absolute and comparative functions. Includes RS232 interface port. Supplied with scriber foot and clamp. Powered by SR44W battery(included) and supplied with storage case.Measuring range: 0 - 200mm / 0 - 8in 200 - 300 / 8 - 12inAccuracy: 0.03 / 0.0012in 0.04mm / 0.0015inResolution: 0.01mm / 0.0001inRepeatability: 0.01mm / 0.0005in1 Power switch2 mm / inch selection3 Relative / Absolute4 Zero setting button5 + preset button6 - preset buttonA ScaleB BeamC Fine adjustmentD LCD DisplayE Interface (serial)F Fastening ScrewG Battery lidH BaseI ScriberOperating temperature: 0 - 40∫CStorage temperature: -20 - 70∫CMax. relative humidity: 80%3. OPERATION3.1 Turn the gauge on by pressing the power button (Fig 1 #1).3.2 Select the desired units of measurement (inch / mm) using the selection button (Fig 1 #2).3.3 Select Relative or Absolute measuring mode (Fig 1 #3).Note: Relative measuring mode is used for making comparative measurements e.g. the difference in height between two points/objects.When Relative measuring is selected, the display will be set to zero. Absolute mode can be reselected at any time, to measure theactual height of a point/object.3.4 To set the gauge to absolute zero at any point, press the Zero setting button (Fig 1 #4).3.5 To set the origin to a value other than zero, use the +/- preset buttons (Fig 1 #5 #6).3.5.1 To increase the value of the origin, press the zero setting button and + preset button simultaneously. The word ìsetî will flash in the display.To increase the value by 0.01mm or 0.001î press the + preset button once. To increase the value further, keep the + preset buttondepressed until the desired value has been set. Press the zero setting button once more to return to measuring mode.3.5.2 To decrease the value of the origin, repeat step 3.5.1, this time using the - preset button.3.6 To fit the scriber:3.6.1 Place the clamp upon the arm extending from the slider.3.6.2 Slot the scriber into the clamp and tighten.ArmClampScriberAK9636D - 1 - 110803Fig 2

/ 2

Related manuals for Sealey AK9636D