Panasonic Viera TX-26LXD600 Operating Instructions Manual

Also see for Viera TX-26LXD600: Quick start guide Service manual

Panasonic Viera TX-26LXD600 Operating Instructions Manual Manual pdf 27 page image

52FAQs, etc.53Problem Actions• On screen messages• Frequently Asked QuestionsFAQs Problem ActionsOn screen messages Actions / MeaningsOn screen messagesScreen Sound DVB• Due to the digital reception technologies involved, quality of the DTV signals may be relatively low insome cases, despite good reception of analogue programmes.Chaotic image, noisy • Set "P-NR" in the Picture menu (to remove noise). (p. 23)• Check nearby electrical products(car, motorcycle, fluorescent lamp).No image can bedisplayed • Is "Colour" or "Contrast" in the Picture menu set to theminimum? (p. 23)Blurry or distorted image(no sound or low volume) • Reset channels. (p. 30 and p. 32)No sound is produced • Is "Sound Mute" active? (p. 7)• Is the volume set to the minimum?Sound level is lowor sound is distorted • Sound signal reception may be deteriorated.• Set "NICAM" (p. 22) in the Sound menu to "Off".(Analogue only)Interference orfrozen / disappearingimage in DVB• Check "Signal Condition". (p. 30)If "Signal Quality" or "Signal Strength" are displayed in red,check aerial.If problem persists, consult your local Panasonic dealer.• Use the remote control to turn Off the TV, then turn it On again.Sound is unusual• Set the sound setting of the connected equipment to"2ch L.PCM".• Check the "HDMI1 input" setting in the Sound men u. (p. 23)• If digital sound connection has a problem, select analoguesound connection. (p. 23)Pictures from externalequipment are unusualwhen the equipment isconnected via HDMI• Is the HDMI cable connected properly? (p. 46)• Turn Off the TV and equipment, then turn them On again.• Check an input signal from the equipment. (p. 49)• Use an equipment compliant with EIA/CEA-861/861B.“Control with HDMI” functiondoes not work • Switch the TV on again with the equipment on.• Set “Control with HDMI” to “Off”, then set to “On” again.(p. 44)The SD card cannot be usedeven when it is formatted • Contact the authorized Service Centre.SDHDMIAll tuning data will be erased • "Shipping condition" will erase all tuning data.Are you sure ? • Make sure the operation is with your desire.Are you sure you want to delete this timer ?Press OK to delete timerPress Exit to return • Make sure the deleting programme event is with your desire.Bad Signal • The signal is weak. Check the aerial.DOWNLOAD IN PROGRESS PLEASE WAIT • Q-Link channel download is in progress.DVB Tuner LockedThis programme is locked for recording • If you want to unlock, cancel Direct TV Recording (p. 42) or TimerProgramming (p. 36).Feature not available • Check the Q-Link connection and setting (p. 42).• The impossible source (Component / HDMI / PC) to be record.Incorrect PIN Number • The PIN number you entered is wrong.Invalid DVB Channel • Invalid DVB channel is selected.Invalid system time. Please exit ! • Cannot get the time information. Check the connection of the RF cable.Key not available • You cannot select the same input source between Main and Subscreen when you are viewing in multi window. (p. 13)Max number of Timer already set ! • Maximum timer programming event is 8.New DVB Service Found!Press OK start Auto SetupPress EXIT to Ignore.Warning! Selecting Auto Setup will deletecurrent Profile and Childlock settings• There is a new DVB station.New version 1.90 found.Do you really want to update thesoftware and reboot the system ?Press OK to download the new versionPress EXIT to Ignore• There is a new software available.No DVB Service found • No DVB signal can be found in Auto Setup.No module inserted • Check the CI module inserted completely (p. 27).No recording -Check Tape or Disc • The tape or disc may be "write protected", missing or damaged.The equipment may already be recording.No recording - UNKNOWN REASON • The recording cannot be done by any reason. Check the equipment.• Disc or tape may be full.No Service • The station stops the services.No Signal • Check the connection of the RF cable.Please check aerial or localDVB service availability.Press OK to start Auto Setup • Please follow the message.If it is still failed, consult your local Panasonic dealer.Please check settings and connections on HDMI devices. • Communication error in Control with HDMI function (p. 44).No stations foundPlease insert the aerial • No analogue signal can be found in Auto setup.Please wait. • A function is in progress.Recording in progress • The recording equipment is recording the programme signal fromits own tuner. You can turn the TV off and leave the equipmentrecording in the normal way.Recording stopped - TV source changed • Direct TV recording (analogue mode) will stop if channel or inputsource is changed.Software successfully updatedPress EXIT to continue • The software updating is finished.Software Update failed. Please try again later. • Perform "System Update Search Now" in System Update (p. 27).If it is still failed, there may not be the new software.Press EXIT to continueThis service is locked!Press OK to enter PIN • The selected channel is locked in Child Lock (p. 29).Timer already expired ! • Starting time in Timer Programming is already past. Set correctly (p. 37).Timer Event Due to Start1: BBC1 has beenProgrammed for recording at 20:00 • This message will appear 2 minutes before timer programmingevent due to start.Timer incorrect ! • Set Starting and Ending times in Timer Programming correctly (p. 37).Timer overlap! • The timer programme events are overlapped. Cannot record otherchannel at the same time. Check the Starting and Ending times inTimer Programming (p. 37).Unable to download, Check Equipment • The tape or disc is active. Stop the equipment and try again.WARNINGAll analogue tuning data will be erased • Auto setup will be erased all present analogue tuning data (p. 33).WARNINGAll digital tuning data will be erased • DVB Auto Setup will be erased all present DVB tuning data(p. 30).OtherTV goes into"Standby mode" • The sleep function is activated.• The TV enters "Standby mode" about 30 min.after broadcasting ends.The remote controldoes not work • Are the batteries installed correctly? (p. 6)• Has the TV been switched On?

/ 28

Related manuals for Panasonic Viera TX-26LXD600