Panasonic VIERA TX-26LXD6 Operating Instructions Manual

Also see for TX-23LXD60: Quick start guide

Panasonic VIERA TX-26LXD6 Operating Instructions Manual Manual pdf 47 page image

47S If the external device has DVI output only, use a DVI to HDMI adapter cable to connect to the HDMI1 terminal only.S Connect the audio cables to the AUDIO IN terminals when using a DVI to HDMI adapter cable.(Use only a fully compliant HDMI cable (fully wired)S Select the audio setting in HDMI input. See page 19Compatible sampling frequency of AUDIO signal through HDMI (L.PCM) : 48kHz / 44.1kHz / 32kHzSThis HDMI connector is type A.SIf you connect equipment without a digital output terminal, connect to the COMPONENT, S--Video or VIDEO input terminal onthe TV so you can receive an analogue signalSThe HDMI IN terminal can only be used with 480i, 480p, 576i, 576p, 720p or 1080i picture signals. Set the Digital Set Top BoxDIGITAL OUT terminal output setting to 480i, 480p, 576i, 576p, 720p or 1080i. For detailed information, refer to the Digital SetTop Box instruction manual. If you cannot display the picture because your Digital Set Top Box does not have a DIGITAL OUTterminal output setting, use the component input (or the S--Video input or Video input). In this case the picture will be displayedas an analogue signal.SHDMI--compliant devices will always display the HDMI Logo.SAlways use a fully compliant HDMI cable (fully wired).SHDMI2 terminal is for digital audio signal only.SWhen viewing a 1080i input source it is normal for the picture to show line jitter.SWhen viewing a Component or HDMI source then AV--Monitor Out is not available.A dAspect Control SignalsSignal nameAspect modes Widescreen signal (WSS) Control signal throughSCART (pin8) or HDMIterminalSignal name“o” indicates available“---” indicates unavailableAutoAspect16:9 14:9 4:3 Zoom1Zoom2Zoom3TV AV1AV2AV3Com-ponentAV1 AV2 HDMI1 HDMI2PAL I o o o o o o o o o o o --- o o --- ---TV/ PAL 525/60 o o o o o o o o o o o --- o o --- ---TV/AV1/AV2/ DVB o o o o o o o o --- --- --- --- o o --- ---AV1/AV2/ MNTSC o o o o o o o --- --- --- --- --- o o --- ---AV3 NTSC/AV(Input only)o o o o o o o --- --- --- --- --- o o --- ---Co525(480)/60i o o o o o o o --- --- --- --- --- --- --- o oomp S 525(480)/60p o o o o o o o --- --- --- --- --- --- --- o opoSD 625(576)/50i o o o o o o o --- --- --- --- o --- --- o one 625(576)/50p o o o o o o o --- --- --- --- --- --- --- o oent750(720)/50p o o o o o o o --- --- --- --- --- --- --- o ot/H H 750(720)/60p o o o o o o o --- --- --- --- --- --- --- o oHDMHD 1125(1080)/50i o o o o o o o --- --- --- --- --- --- --- o oMI 1125(1080)/60i o o o o o o o --- --- --- --- --- --- --- o oCONNECTIONS (HDMI)Set Top BoxDVD PlayerUse only a fully compliant HDMIcable(fully wired)NOTESIf adding new equipment or reconnecting equipment or changing setup,using the TV/AV button on the remote control to select the correctconnection (i.e. HDMI1 or HDMI2). (See page 44)SThis input terminal is not intended for use with computers.S720p/1080i signals will be re--formatted to view on your displaySIf the external devices have aspect adjustment, set to 16:9SFor applicable HDMI signals information see page 47.SNon--HDMI--compliant cables cannot be utilized.SIt is recommended that you use Panasonic’s HDMI cable.Recommended part numbers:RP--CDHG15 (1.5 m)RP--CDHG30 (3.0 m)RP--CDHG50 (5.0 m)