Panasonic SC-AK330 Operating Instructions Manual

Also see for SA-AK230: Operating instructions Service manual Service manual Service manual

Contents

Panasonic SC-AK330 Operating Instructions Manual Manual pdf 11 page image

RQT779011You can use either deck 1 or deck 2 for tape playback.Use normal position tapes.High position and metal position tapes can be played, but the unit willnot be able to do full justice to the characteristics of these tapes.1 Press [:, TAPE].The unit comes on.If a cassette was loaded, play starts automatically (One touch play).2 Press [c DECK1] or [DECK2 c] and insert the cassette.Insert with the side to be playedfacing towards you and theexposed tape facing down.Close the holder by hand.3 Press [:, TAPE] to start playback.To play on the other side of the tape, turn the tape over and press[:, TAPE].To stop tape playbackPress [L, STOP].To fast-forward or rewindPress [g/REW/3] (rewind) or [f/FF/4] (fast-forward).To select between loaded decksPress [DECK 1/2] (remote control: [PLAY MODE]).Note• Tape playback is momentarily interrupted if you open the other deck.• Tapes exceeding 100 minutes are thin and can break or get caughtin the mechanism.• Tape slack can get caught up in the mechanism and should betaken up before the tape is played.• Endless tapes can get caught up in the deck’s moving parts if usedincorrectly.CassettesFront sidePlaybackRecordingTo stop recordingPress [L, STOP].If the tape finishes before the discThe disc continues playing. Press [L, STOP] to stop it.To record on the other side of the tapeTurn the tape over and press [a, REC].Note• Changes to volume and sound/field quality do not affect recording.• You cannot open deck 1 while recording.• You cannot fast-forward or rewind one deck while recording withthe other.• When recording an AM broadcast, sound is momentarily interruptedwhen you start and stop the recording.Erasure preventionUse a screwdriver or similar object to break out the tab.To re-record on a protected cassetteCover the hole with adhesive tape.To erase a tape1. Press [:, TAPE] and then [L, STOP].2. Insert the recorded tape into deck 2.Ensure there is no tape in deck 1.3. Press [a, REC].Selection of tapes for recordingUse normal position tapes.High position and metal position tapes can be used, but this unit willnot be able to record or erase them correctly.Preparation:Wind up the leader tape so recording can begin immediately.1 Press [DECK2 c] and insert the cassette to be recorded.Insert with the side to be recorded facing towards you and theexposed tape facing down.2 Select the source to be recorded.Radio recording:Tune in the station. (A page 10)Disc recording:1 Insert the disc(s) you want to record.Press [:/J, CD] and then [L, STOP].2 Prepare the desired disc recording mode.Remote control only• To record programmed tracksOn page 8, “Program play”, do steps:CD 1 ~ 3MP3 1 ~ 4• To record specific discs/tracks1. Press [PLAY MODE] to select the desired mode.(A page 7)2. Press [DISC] and then [1]–[5] to select the disc.Ensure disc is stopped.3. MP3 For 1-ALBUM mode and 1-SONG mode: Press[ALBUM ( or )] to select the album.4. For 1-SONG mode: Press [g, REW/3] or [f,4/FF] to select the track.Tape-to-tape recording:1 Press [:, TAPE] and then [L, STOP].2 Press [c DECK1] and insert the cassette you want to record.3 Press [a, REC] to start recording.Side ATab for side B Tab for side AAdhesive tapeRemote control onlyThis is a 12-hour clock.1 Switch on the power.2 Press [SHIFT] + [CLOCK/TIMER] to select “CLOCK”.Every time you press the button:3 (Within 7 seconds or so)Press [g, REW/3] or [f, 4/FF] to set the time.4 Press [SHIFT] + [CLOCK/TIMER] to finish setting thetime.The display will return to whatever was displayed before you setthe time.To display the timePress [SHIFT] + [CLOCK/TIMER] once when the unit is on or atstandby mode.The time is shown for about 5 seconds.NoteReset the clock regularly to maintain accuracy.Previous displayCLOCK RECPLAYSetting the time