Panasonic SC-AK330 Operating Instructions Manual

Also see for SA-AK230: Operating instructions Service manual Service manual Service manual

Contents

Panasonic SC-AK330 Operating Instructions Manual Manual pdf 10 page image

RQT779010H.BASSH.BASSAutomatic presettingDo the following once each for FM and AM.Preparation: Tune to the frequency where pre-setting is to begin.Hold down [PROGRAM] until the frequency changes.AK330AK230The tuner presets all the stations it can receive into the channels inascending order. When finished, the last station memorized is tuned in.Manual presettingPre-set the stations one at a time.1 Press [PROGRAM] then press [g, REW/3 ] or[f, 4/FF] to tune to the desired station.2 Press [PROGRAM] then press [g, REW/3 ] or[f, 4/FF] to select a channel.3 Press [PROGRAM].The station occupying a channel is erased if another station is presetin that channel.Selecting channelsPress the numbered buttons to select the channel.To enter a 2-digit channel, press [>10], then the two digits.AK330 AK230OR1 Press [PLAY MODE] to select “PRESET”.2 Press [g, REW/3] or [f, 4/FF] to select thechannel.1 Press [TUNER, BAND] to select band.The unit comes on.Every time you press the button:FM AM2 Press [PLAY MODE] on the remote control to select“MANUAL”.Every time you press the button:MANUAL PRESET3 Hold down [g/REW/3] or [f/FF/4] for a momentto search for a station.The frequency stops when it finds a clear station.To stop during the process, press [g/REW/3] or [f/FF/4].Under excessive interference, a station may not be found.Press [g/REW/3] or [f/FF/4] repeatedly to tune step-by-step.“TUNED” is displayed when a radio station is tuned.“ST” is displayed when a stereo FM broadcast is being received.If noise is excessive in FMRemote control onlyHold down [PLAY MODE] to display “MONO” .Monaural sound is selected and noise reduces when reception isweak.Hold down [PLAY MODE] again to cancel the mode.“MONO” is also cancelled if the frequency is changed.To receive FM broadcasts allocated in 0.1 MHz stepsMain unit onlyHold down [TUNER, BAND]. The display changes in a few seconds toshow the current minimum FM frequency. Continue to hold down thebutton until the minimum frequency changes. The step is changed.Repeat the above to change the step back.Note• After changing the “allocation” setting, the frequencies you previouslypreset in the memory will be cleared.• Sound is momentarily interrupted if you load/unload tapes whilelistening to an AM broadcast.Manual tuningRadioRadioOptional antenna connectionsUse outdoor antenna if radio reception is poor.FM outdoor antenna• Disconnect the FM indoor antenna.• The antenna should be installed by a competent technician.AM outdoor antennaRun a piece of vinyl wire horizontally across a window or otherconvenient location.Leave the loop antenna connected.NoteDisconnect the outdoor antenna when the unit is not in use.Do not use the outdoor antenna during an electrical storm.Preset tuningRemote control onlyThere are two methods of pre-setting stations.Automatic presetting : All the stations the tuner can receive are preset.Manual presetting : You can select the stations to preset and theorder they are preset in.Up to 15 stations each can be set in the FM and AM bands.Preparation:Press [TUNER, BAND] to select “FM” or “AM”.5 -12 m(16 – 40 ft.)12AM outdoor antenna (not included)AM loopantenna(included)Rearpanelof thisunit130 mm(1 3/16”)15 mm( 19 /32”)1232FM outdoor antenna(not included)75 Ω coaxial cable (not included)Shield braidCore wireDISCPROGRAMPLAY MODEALBUM ( or )TUNER, BANDc DECK1a, RECTUNER, BAND L, STOPDECK 1/2g/REW/3,f/FF/4Numberedbuttonsg, REW/3,f, 4/FFCLOCK/TIMERSHIFTDECK2 c:, TAPE:/J, CDRearpanelof thisunit