Panasonic Diga DMR-BS750EB Operating Instructions Manual

Contents

98RQT9430Channel Settingsfreesat Channel ListYou can set channel list of freesat.1 Press [e, r] to select “freesat Channel List”, then press [OK].RETURNfreesat Channel List115 ITV3116 ITV3+1Hide117 ITV4118 ITV4+1120 Channel 4121 Channel 4+1122 E4Page UPPage Down CHSelect2 Press [e, r] to select the channel.To hide unwanted channelsPress [OK]. The check mark disappears.You cannot select it by pressing [1, 2 CH].(But you can select it by pressing the numbered buttons to enterthe channel number directly.)Press [OK] again to reveal.freesat Auto SetupYou can restart auto setting for freesat channels if the setup(➔ 13) fails for some reason.However, if you perform “freesat Auto Setup”, all channel settingsare deleted. Confirm the programme you set the timer recordingafter freesat Auto Setup. Please reset it if the setting information isnot correct. Recordings on the HDD are not be deleted.1 Press [e, r] to select “freesat Auto Setup”, then press [OK].When the confirmation screen appears2 Press [w] to select “Yes”, then press [OK].TipsYou can also use the following method to restart freesatAuto Setup. When the unit is turned on and stopped,press and hold [2 CH] and [CH 1] on the main unitsimultaneously for about 5 seconds.freesat Auto Setup screen appears.•–Other Satellite Channel ListYou can set channel list of other satellite services.1 Press [e, r] to select “Other Satellite Channel List”, then press[OK].2 Press [e, r] to select the channel.Press the “Red” button to delete the channel.Press the “Green” button to swap the channel. And, press thenumbered buttons to enter the channel number you want toswap, then press [OK].Press the “Yellow” button to sort channels.Press the “Blue” button to profile the channel.To hide unwanted channelsPress [OK]. The check mark disappears.You cannot select it by pressing [1, 2 CH].(But you can select it by pressing the numbered buttons to enterthe channel number directly.)Press [OK] again to reveal.••••Other Satellite Tuning MenuYou can tune channels from other satellites.Press [OK] to show the following settings.RETURNOther Satellite Tuning MenuAuto SetupManual TuningOKAccessDish Setup•Auto SetupYou can start the auto setup of the other satellite services.(➔ 16, Tuning in Other Satellite Services)RETURNOther Satellite Auto Setup - Satellite Selectionfreesat and other satellite channelsSatellite SelectionSearch ModeStartSelectChangeAstra2/EurobirdAllChannel Type AllManual TuningYou can set the channel of the other satellite manually.RETURNOther Satellite Manual TuningTranspounder FrequencyPolarisationStart ScanSelectHorizontal10773Symbol Rate (Ksym/s) Auto0 - Enter Frequency91 Press [e, r] to select “Transpounder Frequency”2 Press the numbered buttons to enter the transpounderfrequency.3 Press [e, r] to select “Polarisation”.4 Press [w, q] to select “Horizontal” or “Vertical”.5 Press [e, r] to select “Symbol Rate (Ksym/s)”.6 Press [w, q] to select the desired symbol rate, then press [OK].–The scan starts.Dish SetupYou can set the dish setup manually.RETURNEXITDish SetupSatellite services may not be available if changed!LNB Low Band Frequency (MHz)LNB High Band Frequency (MHz)Select10600975022KHz Command On0 - Enter Frequency9Reset all1 Press [e, r] to select “LNB Low Band Frequency (MHz)”.2 Press the numbered buttons to enter the LNB Low Bandfrequency.3 Press [e, r] to select “LNB High Band Frequency (MHz)”.4 Press the numbered buttons to enter LNB High Bandfrequency.5 Press [e, r] to select “22KHz Command”.6 Press [w, q] to select “On” or “Off”.Press the “Red” button to reset all settings.•Signal ConditionYou can check the quality and strength of digital satellite broadcastsignals. Realign the dish if you are receiving a poor signal.1 Press [e, r] to select “Signal Condition”, then press [OK].2 Press [w, q] to select the input you want to check.RETURNSatellite Signal ConditionDish InputChannel NameChange InputInput 1101 BBC 1 WalesNetwork ID 003BTransport Stream ID 07FFSatellite Lock Indicator Not LockedChannel UPChannel DownSignal QualitySignal Strength0 100 1012CHThe quality and strength of the signal are shown. Press [1, 2 CH]to select the channel.Signal QualityBelow 2 (display red) The signal quality is so poor that there maybe interference in the pictures and sound.2–5 (display orange) The signal quality is basically adequate, butbrief interference in the pictures and soundis possible in isolated case.Over 5 (display green) Optimum picture and sound quality.