Panasonic BL-C20A Getting Started

Also see for BL-C20A - Network Camera: Operating instructions Troubleshooting Operating instructions

Contents

Panasonic BL-C20A Getting Started Manual pdf 2 page image

NetCamWhen the Single Camera page is displayed, setupis complete.Click [Next] to set up the Internet access to the cam-era and go to step in "To Set Up Internet Accessto the Camera".Enter the user name and password, and click [Save].The Enter Network Password window is displayed.Enter the user name and password that were set, andclick [OK].Make a note of the user name and password.To ensure that the most current imageis displayed, Internet Explorer shouldbe configured as follows. This will nothave a negative effect on normal use.1. While viewing any website, click[Tools] [Internet Options].2. In the section "Temporary InternetFiles", click [Settings] and check[Every visit to the page].• If the Security Warning window is displayed when installing ActiveX®Controls, click [Yes].• To install ActiveX Controls on Microsoft® Windows® XP Service Pack2, see "Security Warning window on Microsoft Windows XP ServicePack 2" on the next page.• Click [Cancel] and go to the lastpage if you will mount the camera.• If you set wireless configuration,confirm the wireless LAN setupseeing the next page.• This program searches for the cameras that are connected to the routerand displays their MAC Addresses, IP addresses and Port Numbers.• The MAC Address on the rear side (see page 6 of the OperatingInstructions on the CD-ROM.) of the camera shows which camera youselect on the camera list window.If more than 20 minutes have passed since the camera was turned on, thecamera cannot be set up from the Setup Program. In this situation, restart thecamera.NoteNote1234Set the Wireless Configuration according to the wirelesssettings of the router and click [Next>].• For more information about wireless setting, seehttp://panasonic.co.jp/pcc/products/en/netwkcam/1. Set the SSID.Set the name of the wireless network.2. Select the Communication mode.These are IEEE Communication modes. Select the same Communication mode asthat of the router to which the camera is connected.802.11b (IEEE802.11b) : Only the 802.11b wireless router can be connected.802.11b/g (IEEE802.11g) : Either the 802.11b or 802.11g router can beconnected.802.11g exclusive (IEEE802.11g) : Only the 802.11g router can be connected.3. Select encrypting or not encrypting.Selecting WEP can encrypt data within the wireless LAN.WEP: Encrypting (setting WEP) makes it difficult for unauthorized users to readdata within the wireless LAN, even if they can receive it. To encrypt data, setthe same encryption key to every terminal within the wireless LAN. There are3 kinds of encryption key: 64 bit, 128 bit and 152 bit. Security level ofencryption increases in order of length as follows: 64 bit, 128 bit and 152 bit.No encryption: select when not using encryption.4. Set the WEPKey1–4.Selecting [WEP] at Cipher enables you to set WEPKey1–4. One or all of the fourkeys can be set. Check the key number set to the router, and set the same key as atthe router.: The entered WEPKey will be displayed as " "s regardless of the keytype selected.HEX, 10 characters 64 bit : 012345abcdHEX, 26 characters 128 bit : 0123456789abcdef012345abcdHEX, 32 characters 152 bit : 0123456789abcdef0123456789abcdefASCII 5 characters 64 bit : 012yzASCII 13 characters 128 bit : 0123456uvwxyzASCII 16 characters 152 bit : 0123456789uvwxyz• Wireless Configuration can alsobe set at on the SetupPage. (See page 36 of theOperating Instructions on theCD-ROM.)Click [Automatic Setup (Local Access Only)].Click [Automatic Setup (Internet Access)].The Enter Network Password window is displayed. Enter theuser name and password that were set, and click [OK].Select the camera on the camera list to set up theInternet access and click [Execute].When using a router that supports UPnP TM , check [Enable].When using a router that does not support UPnP TM , check[Disable]. Then click [Next>].• Check if your router supports UPnPTM referring to the router'smanual.• If you select [Disable], skip to step on the next page.NoteCameraList windowCameraStatusPortNo.MACAddressIPAddressTo set Wireless Configuration, check [Enable] and click [Next>].• When [Disable] is selected, skip to step .3. Set up Internet access to the camera.

/ 4

Related manuals for Panasonic BL-C20A - Network Camera