Panasonic BL-C1A Getting Started

Also see for BL-C1A - Network Camera: Operating instructions Troubleshooting Operating instructions

Contents

Panasonic BL-C1A Getting Started Manual pdf 4 page image

Security Warning window on Microsoft Windows XP Service Pack 2To view a video (Motion JPEG), ActiveX Controls must be installed. Follow the steps shown below to install ActiveX Controls.Click the warning displayed above the tabs, and click [InstallActiveX Control...]. Click [Install].4. Mount the camera.The camera can be mounted in the following ways.• Do not mount the camera where the sun light directly hits the camera or inoutdoor-type housing without a temperature control system. The cameramay malfunction due to high temperature.• When you mount the camera, always hook the AC adaptor cord to thehook.• This product is for indoor use only. Do not use it outdoors.• The camera may become warm. This is not a malfunction.• Mount the camera where the AC adaptor can reach an outlet, or use an extensioncord (customer-provided).• Do not mount the camera upside down, as the image will be displayed upsidedown.NoteMake sure the indicator isalways in the upper rightcorner.TopBottomHook forAC adaptor cordStand Mount Tripod MountStand/TripodMounting HoleFlexibleStandDisconnect all cables from the camera. Reconnect the cables after mounting thecamera.NoteLoosen the Position Locklocated on the rear side ofthe flexible stand.• Do not use a tripod screwwith a thread of 6 mm (1/4inch) or more. (This maydamage the Stand/Tripodmounting hole.)• The camera cannot bemounted depending on theshape of the cameraplatform.Adjust the angle, then fastenthe Position Lock.Stand/TripodMounting HoleTripod(customer-provided)MountingScrew PositionLockTurn the Mounting Screw toattach the camera.NoteCeiling Mount• Do not mount the camera upside down, as the image will be displayed upsidedown.• We recommend only mounting the camera using the provided hardware.Mounting in any other manner may cause the camera to fall, resulting inpersonal injury or damage to the camera.• To reduce the load on the mounting hardware, dress the cables neatly andsecure with tape.• Disconnect all cables from the camera. Reconnect the cables after mountingthe camera.Note• Do not mount the camera on a softmaterial. The camera may fall andbe damaged.• Use appropriate screws for thematerial of the ceiling.Mount the flexible stand firmly to theceiling with the two screws (included).Loosen the Position Lock locatedon the rear side of the flexible stand,and turn the Mounting Screw toattach the camera.Adjust the angle, then fastenthe Position Lock.Connect the AC adaptor cord andthe Ethernet cable to the camera.Dress the cables neatly and securewith tape (customer-provided).ScrewsAllow sufficient spacebetween the wall and theflexible stand to turn thePosition Lock.Stand/TripodMounting HoleTape(customer-provided)Mounting ScrewPosition LockPosition LockWall Mount• Do not mount the camera upside down, as the image will be displayed upsidedown.• We recommend only mounting the camera using the provided hardware.Mounting in any other manner may cause the camera to fall, resulting inpersonal injury or damage to the camera.• To reduce the load on the mounting hardware, dress the cables neatly andsecure with tape.• Disconnect all cables from the camera. Reconnect the cables after mountingthe camera.Note• Do not mount the camera on a softmaterial. The camera may fall andbe damaged.• Use appropriate screws for thematerial of the wall.Mount the flexible stand firmly to thewall with the two screws (included).Loosen the Position Lock locatedon the rear side of the flexible stand,and turn the Mounting Screw toattach the camera.Connect the AC adaptor cord andthe Ethernet cable to the camera.Dress the cables neatly and securewith tape (customer-provided).Adjust the angle, then fastenthe Position Lock.ScrewsAllow sufficient space between theceiling and the flexible stand to turnthe Position Lock.Position Lock Tape(customer-provided)Stand/TripodMountingHoleIndicatorMountingScrewPositionLock

/ 4

Related manuals for Panasonic BL-C1A - Network Camera