Panasonic AW-RP305 Service Manual

Also see for AWRP301 - PAN/TILT CONTROL PAN: Operating instructions Operating instructions

Contents

Panasonic AW-RP305 Service Manual Manual pdf 3 page image

1MAJOR OPERATING CONTROLS AND THEIR FUNCTIONSS P E E D F O C U S P A N / T I L TZ O O MT E L EW I D EF A RL E F T R I G H TU PD O W NN E A RD E FO NO F FP O W E RI R I SO NO F FL A M P M E M O R YO NO F FA U T OM A N UO NO F FO NO F FO NO F FO NO F FO NO F FW I PE X T N D O PH / FP R E S E TP a n / T i l t C o n t r o l P a n e l A W - R P 3 0 121 3 4 56 7 8 9 1 0L E V E LTALLY Control Panel AW-RP301 AW-RP305S P E E D F O C U S P A N / T I L TZ O O MT E L EW I D EF A RL E F T R I G H TU PD O W NN E A RD E FO NO F FP O W E RI R I SO NO F FL A M P M E M O R YO NO F FA U T OM A N UO NO F FO NO F FO NO F FO NO F FO NO F FW I PE X T N D O PH / FP R E S E TM u l t i P a n / T i l t C o n t r o l P a n e l A W - R P 3 0 51 54321 543221 3 4 56 7 8 9 1 0L E V E LT A L L YC O N T R O Lq Power Indicator [POWER]Lights red when POWER ON/OFF Switch w is in the ONposition, and goes out when the same switch is set tothe OFF position.w Power Control Switch [POWER, ON/OFF]All the connected pan/tilt heads are switched on whenthis switch is set to the ON position. (The power indica-tor lights.) The pan/tilt head are partially switched offwhen this switch is set to the OFF position.Note: When the switch is set to the OFF position, thecommunication line between the pan/tilt head andthis control panel remains live. To disconnect allpower supply, pull out the power plug from the elec-trical outlet.e Tally Indicator [TALLY]On the AW-RP305, the LED corresponding to theTALLY Terminal @1 from a Special Effect Generator(SEG) or video switcher. On the AW-RP305, the LEDcorresponding to the TALLY Terminal @1 (one of [1] to[5]) to which a tally signal is input lights red.r Pan/tilt Head Selection Switch [CONTROL](AW-RP305 only)Select a desired camera with pan/tilt head from amongthose connected to the control panel. When a camerawith pan/tilt head is selected by pressing one of the but-tons [1] to [5], the pressed button lights.Note: Even if an unconnected camera with pan/tilt headis selected by pressing the corresponding button,the button lights.t Lamp Indicator [LAMP]Lights red when LAMP ON/OFF Switch y is in the ONposition. Flashes if the lamp connected to the ACAdapter (AW-PS300) for pan/tilt head is broken.Goes out when LAMP ON/OFF Switch y is set to theOFF position.Note: Use a halogen lamp of 250 W to 500 W to con-nect to the pan/tilt head AC Adapter (AW-PS300).If a lamp of lower than 250 W is connected to it, theLED may flash when LAMP ON/OFF Switch y is inthe ON position even though the lamp is not broken.y Lamp Switch [LAMP, ON/OFF]Switches on and off the halogen lamp connected to thelamp AC receptacle of the Pan/tilt Head AC Adapter(AW-PS300). In case of the AW-RP305, first select apan/tilt head with CONTROL Switch r, then switch onor off the lamp. Set it to the ON position to switch thehalogen lamp on (in which case, the lamp LED flashes).Set it to the OFF position to switch the halogen lamp off.Note: In using the AW-RP305, when a pan/tilt head isselected with CONTROL Switch r, the halogenlamp connected to the AC adapter for the pan/tilthead selected with that switch lights or goes outdepending on the position of LAMP ON/OFF Switchy.u Lens Iris Selection Switch [IRIS, AUTO/MANU]Select a lens iris selection mode with this switch. Whenthis switch is in the AUTO position, the lens iris is auto-matically controlled according to the quantity of lightentering the lens. When the switch is in the MANU posi-tion, the iris can be manually controlled over the rangefrom the closed position to the fully open position usingIRIS LEVEL Control i.Set the switch to the MANU position in storing iris datain PRESET Switches !0 with MEMORY Switch o. Ifthe switch is in the AUTO position, iris data will not bestored in the memory.Note: Len iris data may be unable to be stored in thememory depending on the camera connected.