OHAUS RS Series Operator's Manual

Also see for RS Series: Quick start guide

OHAUS RS Series Operator's Manual Manual pdf 14 page image

RS Series Oprator Manual84 Operation4.1 ZeroThere are two ways to re-zero the scale:☞ Power-up zeroThe scale will automatically capture zero when it is turned on. The power-up zero capture range is +/-10% of the scalecapacity. When the scale is turned on with a weight on the platter, which is more than +/-10% of the capacity, the scalewill not capture zero and the weight display will show "-----". After removing the weight, the scale will capture "zero".☞ Pushbutton zeroPress and hold key [Mode], then press [>0<] to re-zero the scale within the range of +/-2% of the scale capacity. To usethis function, the scale must be in the gross weighing mode (NET cursor must be off) and in a no motion condition. Whenthe weight on the platter is more than +/-2% of the scale capacity, scale can not be re-zeroed.4.2 TareTare is a subtract tare. When tare exists, the most the scale can weigh is its full capacity minus tare.Tare can not be cleared unless the net weight is equal to gross weight. Tare function is enabled only when the displayedweight value is positive.4.2.1 Pushbutton TareProcedure Description KeyoperationDisplayon 1st lineDisplayon 2 nd lineDisplayOn 3 rd lineDisplayon the bottom lineLitcursorStep4 Put the container (20g) on the platter 0.020 0.00 0.00 V1 ticketStep5 Tare and show tare 0.020kg [ÆTÅ] 0.000 0.00 0.00 t 0.020kg NETStep6 Remove the container from the platter -0.020 0.00 0.00 t 0.020kg NETStep7 Clear tare and get back the gross weighing mode [ÆTÅ] 0.000 0.00 0.00 V1 ticket4.2.2 Input Preset Tare ManuallyProcedure Description KeyoperationDisplayon 1 st lineDisplayon 2 nd lineDisplayon 3 rd lineDisplayon the bottom lineLitcursorStep1 Gross weight should be zero 0.000 0.00 0.00 V1 ticketStep2 Please input the tare value [ÆTÅ] 0.000 0.00 0.00 tare 0.000Step3 Input the tare value 1.000kg [1][0][0][0] 0.000 0.00 0.00 tare 1.000Step4 Get tare [ÆTÅ] -1.000 0.00 0.00 Pt 1.000kg NETStep5 Clear tare and get back the gross weighing mode [ÆTÅ] 0.000 0.00 0.00 V1 TicketThe tare value is a multiple of the increment.. If the tare value entered is not a multiple of the increment, then the value will berounded (up or down) to the closest multiple.e.g. If the increment is .005lb and the tare value entered is .007lb, then the scale will use a tare value of .005.4.2.3 Tare DisplayTare will be shown on the bottom line. ”T” means pushbutton tare, ”PT” means preset tare including the tare in PLUIf tare exists, when key [V1] is pressed, the bottom line will show subtotal for about 1~2 minutes, then show tare.Procedure Description KeyoperationDisplayon 1 st lineDisplayon 2 nd lineDisplayon 3 rd lineDisplayon the bottom lineLitcursorStep1 Put the container (20g) on the platter 0.020 0.00 0.00 V1 ticketStep2 Tare is 20g [ÆTÅ] 0.000 0.00 0.00 t 0.020kg NETStep3 Recall PLU1 without tare [1] 0.000 9.80 0.00 PLU 1 t 0.020kg NETStep4 Put the item on the platter 0.500 9.80 4.90 PLU 1 t 0.020kg NETStep5 Show subtotal 4.90$ on the bottom line [V1] 0.5 00 0.00 0.00 V1 P1 A 4.90 NETStep6 Show vendor # and tare 0.020kg 1~2 seconds later 0.5 00 0.00 0.00 V1 t 0.020 NETStep7 Remove the container from the platter -0.020 0.00 0.00 V1 t 0.020 NETStep8 Clear tare and show the subtotal 4.90$ [ÆTÅ] 0.000 0.00 0.00 V1 P1 A 4.90