NEC PX-42XM4A User Manual

Also see for 50XM5A: Supplementary guide Specifications Installation guide

Contents

NEC PX-42XM4A User Manual Manual pdf 24 page image

En-23Option1 Settings MenuSetting the on-screen menuThis sets the position of the menu, the display format(horizontal or vertical) etc.Example: Turning the DISPLAY OSM offOn “OPTION1” menu, select “OSM”, then press the MENU/ENTER button.The “OSM” menu appears.On “DISPLAY OSM” of “OSM” menu, select “OFF”.SEL. ADJ. RETURNOSMEXITDISPLAY OSMOSM ADJ.OSM ANGLEOSM ORBITEROSM CONTRAST: OFF: 1: H: OFF: LOWInformation DISPLAY OSM settingsON: The informations on screen size, volume control,etc. will be shown.OFF: The informations on screen size, volume control,etc. will not be shown.The DISPLAY button on the remote control will notfunction either. OSM ADJUST settingsAdjusts the position of the menu when it appears onthe screen.The position can be set between 1 to 6. OSM ANGLE settingsSets the display format (landscape “H” or portrait “V”).When the unit is installed vertically set the OSMANGLE at “V”.“H” “V” OSM ORBITER settingsON: The position of the menu will be shifted by eightdots each time OSM is displayed.OFF: OSM will be displayed at the same position. OSM CONTRAST settingsNORMAL: OSM brightness is set to normal.LOW: OSM brightness is set to lower.Setting the BNC input connector typeSelect whether to set the input of the 5 BNC connectors toRGB or Component.Example: Set the BNC INPUT mode to “COMP.”On “BNC INPUT” of “OPTION1” menu, select “COMP.”.SEL. ADJ. RETURNOPTION 1 1 / 4OSMBNC INPUTD-SUB INPUTRGB SELECT: AUTOHD SELECTINPUT SKIPALL RESETNEXT PAGE: COMP.: RGB: 1080B: OFF: OFFEXITInformation BNC INPUT SettingsRGB: Use the 5BNC terminals for RGB input.COMP.: Use the 3BNC terminals for component input.SEL. RETURNOPTION 1 1 / 4OSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: AUTO: 1080B: OFF: OFFEXITMENU/ENTER OK: RGB: RGB: AUTO: 1080B: OFF: OFF1024768EXITSEL.RETURNMENU/ENTER OKOPTION1OSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETChecking the signal being transmitted toRGB1 terminalUse this to confirm the signal being transmitted to theRGB1 terminal.It is set to RGB and can not be adjusted.CAN NOT ADJUSTOPTION 1 1 / 4OSMBNC INPUTD-SUB INPUTRGB SELECT: AUTOHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: 1080B: OFF: OFFSetting a computer image to the correct RGBselect screenWith the computer image, select the RGB Select modefor a moving image such as (video) mode, wide mode ordigital broadcast.Example: Setting the “RGB SELECT” mode to“852480 ”On “RGB SELECT” of “OPTION1” menu, select“852480”.SEL. ADJ. RETURNOPTION 1 1 / 4OSMBNC INPUTD-SUB INPUTRGB SELECT: 852480HD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: 1080B: OFF: OFFEXITInformation RGB SELECT modesAUTO: Select the suitable mode for the specificationsof input signals as listed in the table “Computer inputsignals supported by this system” on page En-40.The others: The available resolutions are shown.See page En-40 for the details of the above settings.