NAPCO LIBRA LIB-P432EX Programming Instructions Manual

Contents

NAPCO LIBRA LIB-P432EX Programming Instructions Manual Manual pdf 4 page image

LIBRA LIB-P432EX Series Programming Instructions NAPCO Security SystemsPage 4SYSTEM PROGRAMMING OPTIONSINTRODUCTIONThe LIB-P432EX control panel may be programmed by various means, each of which will be covered in detail in thesections that follow. Keypad displays shown are for a GEM-DXK2, GEM-DXRP2, GEM-DXK3, GEM-DXRP3 and GEM-DXK4RF series keypads. With the GEM-DXK2 and GEM-DXRP2 keypads, because of their reduced displaycapabilities, messages are abbreviated and will scroll through two or more screens. Zone descriptions cannot beprogrammed using the GEM-DXK2 or GEM-DXRP2 keypads, therefore a GEM-DXRP1 / GEM-DXK1 must be used (seeWI1690). Downloading From a Computer. This is the preferred method of programming. The panel may be downloadedfrom (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD-WindowsQuickloader software features context-sensitive help screens as well as an error-checking utility that preventsprogramming of incompatible or conflicting data to ensure proper panel operation. Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu-DrivenProgram Mode allows keypad programming of number of zones in area 1, panel zone doubling, number of firezones (both 4-wire and 2-wire), local or Central Station reporting, number of exit/entry zones, number of interiorzones, number of 24 hour zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop responsezones, aux output activated on alarm zones, sensor watch zones, keypad sounder on alarm zones, auto bypassre-entry zones, EOLR zones, number of keypads in area 1, Central Station telephone number, Central Station ac-count number, Central Station receiver format, User Codes, RF transmitter points, RF keyfob transmitters, zonedescriptions, dealer code, Telco line fault test, Burg output chirp on keyfob, enable CP-01, and clear dealer pro-gram/cold start. For new panels, a custom default program may be created at the keypad. A menu-driven utilityprompts the installer to configure the system. Further detailed customization is accomplished in the DirectAddress Program Mode. Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Program Modeis an extension of the Dealer Program Mode wherein data is entered at the keypad by specific location. This modeis accessed from the Easy Menu Driven Program Mode by pressing the y button at any time. User Program Mode - Keypad programming. The User Program Mode is intended for authorized users and islimited to keypad programming of User Codes.DOWNLOADING FROM A COMPUTERThe control-panel program may be downloaded from the computer by any of the following methods.Local Downloading(Note: This procedure should be used after installation, after peripheral devices are connected).For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. ConnectJP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer toPCI-MINI Installation Instructions WI767).Remote Downloading(Also see PCI2000/3000 Installation Instructions WI443).Function Mode.Start by establishing a Telco connection between the computer operator and the installer. During this procedure,voice contact will be lost, therefore both the installer and the computer operator should be familiar with theoperation. When a steady high-pitched tone is heard at the site phone, access the “ACTIVATE DOWNLOAD” Function(see Keypad Programming Modes), then press the u button or the YES ("r" or p) button; the site phone willgo dead. Hang up the phone and wait for a call from the central station confirming a successful download.Callback Method.An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-MethodDownload feature of the PCD Windows software. Remote downloading requires a modem compatible with thePCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and,if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel willautomatically disconnect and call the computer at this number before establishing a connection.