NAD C165BEE Owner's Manual

Also see for C165BEE: Specifications Owner's manual Service manual

Contents

NAD C165BEE Owner's Manual Manual pdf 6 page image

IDENTIFICATION OF CONTROLSfront panel1 StandbY button: With the rear panel POWER switch set to ONposition, press this button to switch ON the C 165BEE from standbymode. The Standby LED indicator will turn from amber to blue. Pressingthe STANDBY button again turns the unit back to standby mode.The C 165BEE can also be switched ON from standby mode by pressingany of the front panel buttons.2 StandbY led: This indicator will light up amber when the C 165BEEis in standby state. When the C 165BEE is at ON state, this indicator willilluminate blue. When infrared command from the SR 8 is received, thisindicator will also flash momentarily.3 phoneS: A 1/4” stereo jack socket is supplied for headphone listeningand will work with conventional headphones of any impedance.Inserting a headphone jack into this socket automatically switches offthe output at PRE OUT 1 and PRE OUT 2 in the rear panel. The volume,tone and balance controls are operative for headphone listening. Usea suitable adapter to connect headphones with other types of sockets,such as 3.5mm “personal stereo” jack plugs.NOTEMake certain that the volume control is turned to minimum (fullycounterclockwise) before connecting or disconnecting headphones.Listening at high levels can damage your hearing.4 remote SenSor: Point the SR 8 remote control at the remotesensor and press the buttons. Do not expose the remote sensor of theC 165BEE to a strong light source such as direct sunlight or illumination.If you do so, you may not be able to operate the C 165BEE with theremote control.distance: About 23ft (7m) from the front of the remote sensor.angle: About 30° in each direction of the front of the remote sensor.5 input SelectorS: These buttons select the active input to theNAD C 165BEE. The buttons on the remote control handset duplicatethese buttons. When selected, the corresponding input LED indicatorembedded around the bezel of the particular input button willilluminate blue.phono: Selects as the active input the turntable connected to eitherthe PHONO MM or MC sockets.cd: Selects the CD (or other line-level source) connected to the CDsockets as the active input.tuner: Selects the tuner (or other line-level source) connected to thetuner sockets as the active input.mp (media plaYer): Selects a line-level source connected to the MPsockets as the active input.aux: Selects a line-level source connected to the AUX sockets as theactive input.tape 2: Selects Tape 2 as the active input.tape monitor: Selects the output from a tape recorder when playingback tapes or monitor recordings that are being made through the TapeMonitor sockets.TAPE MONITOR does not override the current input selection. For example,if CD is the active input when TAPE Monitor is selected, then the CDsignal will continue to be selected and sent to both the TAPE 2 and TAPEMonitor OUTPUT sockets, but it is the sound from recorder connected toTape Monitor that will be heard on the loudspeakers. Apart from the TAPEMONITOR LED illuminated to indicate it is engaged, the corresponding LEDindicator for the active input will also stay illuminated.6 tone defeat: Tone Controls are enabled or disabled by pressing thisbutton. When enabled (TONE DEFEAT LED indicator is illuminated), theTone Control circuits are bypassed. The Tone Control circuits are activewhen the TONE DEFEAT LED indicator stays extinguished.7 tone controlS: The NAD C 165BEE is fitted with BASS and TREBLE tonecontrols to adjust the tonal balance of your system. The 12 o’clock positionis “flat” with no boost or cut, and an indent indicates this position. Rotatethe control clockwise to increase the amount of Bass or Treble. Rotate thecontrol counterclockwise to decrease the amount of Bass or Treble. TheTone controls do not affect recordings made using the Tape output but willaffect the signal going to the Pre-amp output (PRE OUT).8 balance: The BALANCE control adjusts the relative levels of the leftand right channels. The 12 o’clock position provides equal level to theleft and right channels. A detent indicates this position. Rotating thecontrol clockwise moves the balance towards the right. Rotating thecontrol counterclockwise moves the balance to the left. The BALANCEcontrol does not affect recordings made using the Tape output but willaffect the signal going to the Pre-amp output (PRE OUT).9 volume: The VOLUME control adjusts the overall loudness of thesignals being fed to PRE OUT 1, PRE OUT 2 or headphones. Turnclockwise to increase the volume setting; counter clockwise to lower it.The VOLUME control does not affect recordings made using the Tapeoutput but will affect the signal going to the Pre-amp output (PREOUT).19873 4 5 62ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ