NAD C 368 Owner's Manual

Also see for C 368: Quick setup guide Service manual User manual Owner's manual

Contents

NAD C 368 Owner's Manual Manual pdf 14 page image

AUTO STANDBYAuto Standby feature is an integral feature of C 368 that conforms toEuropean ecodesign regulations. The C 368 can be setup to automaticallygo to standby mode if there is no user interface interaction and no activesource input within 30 minutes. The following are the Auto Standby modesettings.NORMAL MODE· C 368 switches to standby mode at lowest power consumption (lessthan 0.5W).· From normal standby mode and with Auto Sense set to “On”, the C 368can be switched to operating mode by an active source input, pressingthe front panel Standby button or remote control’s [ON] button.NETWORK MODE· C 368 switches to standby mode at reduced system performance level.· Network connection is maintained at network standby mode.· At network standby mode and with Auto Sense set to “On”, the C 368can be switched to operating mode using network connected App,active source input or by pressing the front panel Standby button orremote control’s [ON] button.OFF MODE· C 368 remains at operating mode even if there is no user interfaceinteraction and no active source within 30 minutes.AUTO SENSEAuto sense feature enables the C 368 to wake up from standby modewhen triggered by network connected App or active source input.ON· Unit wakes up from standby mode when triggered by networkconnected App or active source input.· Except for analog input, the unit will power up to the Source thatactivated the unit to operating mode.· When the unit is triggered by an active analog input, the unit willalways power up to Line 1.OFF· Unit remains at standby mode even if it is triggered by networkconnected App or active source input.IR CHANNELThe C 368 has the capability to operate via Alternate IR channel. This isuseful if you have two NAD products that can be operated by similarremote control commands. With alternate IR Channel, two different NADproducts can be controlled independently in the same zone by settingeach one to a different IR channel.IR Channel AssignmentThe C 368 and the SR 9 remote control must be set to the same channel.To change the IR Channel on the C 368While at IR Channel menu, use the [a/s] to select through Channel 0 toChannel 3. Press [ENTER] to select preferred IR Channel setting. C 368 IRChannel is defaulted to Channel 0.To change the IR Channel on the SR 9 remote control• Include a channel number before the library code. For SR 9, library code“10” is the default library table for “AMP” device. To select this “AMP”library table for IR Channel 0 (CH0), retain the library code “10” (or “010”).• If you want to load the “AMP” library table on ”IR Channel 1” prefix thelibrary code with “1” to indicate association with “IR Channel 1”. Loadthen the “AMP” library table using the code “110”. Repeat the same forMP (130) and TUNER (140).SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONENAD C 368 and NAD C 390DD are both defaulted to IR Channel 0. If [OFF]button is pressed on the SR 9 remote control (or AVR 4 remote control forthe C 390DD), both products will go to standby mode. Press [ON] and bothproducts will power up from standby mode.To prevent both products from simultaneously going in and out of standbymode along with other common commands, set each one to a differentIR channel. In this setup, we will keep C 390DD and AVR 4 remote controldefaulted to “IR Channel 0. As for C 368, we will assign it to “IR Channel 1”;the same applies to SR 9.Set C 368 and SR 9 to “Channel 1” via the following procedure.C 368While at “IR Channel” menu, use the [a/s] to go to “Channel 1” setting. Press[ENTER] to select “Channel 1”.SR 9• Press and hold [AMP] in the DEVICE SELECTOR section of the SR 9.• While holding down the device button [AMP], press “1”, “1” and “0” usingSR 9’s numeric buttons.• Press [ENTER] while still holding down the device button [AMP]. TheAMP device selector will flash once to indicate that the library input issuccessful.With both C 368 and SR 9 set to “Channel 1”, the C 368 can now beremotely controlled independent of the C 390DD.NOTEPerforming a Factory Reset for C368 or SR 9 will restore their respectiveIR channel setting to “IR Channel 0”.OPERATIONUSING THE C 368IR ChannelSettingsSource SetupChannel 0SettingsAuto SenseSettingsSource SetupOffSettingsAuto StandbySettingsSource SetupNormal ModeSettings14ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ