JVC RX-D302BC Instructions Manual

Also see for RX-D301S: Instructions Instructions Instructions Instructions Service manual

33On the front panel:Before you start, remember...There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step2 again.1 Select and play any source other than DVDMULTI.• Make sure you have selected the input mode (analog ordigital) correctly.2 Press SURROUND.MULTI JOG now works for selecting Surround/DSP modes.3 Turn MULTI JOG to select the Surround/DSPmode you want.Ex.: When “DOLBY DIGITAL” is selected for Dolby Digitalmulti-channel software:*1 “AUTO SURROUND” is the initial setting.*2 Available Surround modes vary depending on the speakersettings and the incoming signals. For details, see page32.*3 If an incoming signal is a multi-channel (more than 2channel) digital signal, “MONO FILM” is not available.*4 If “SURROUND SPK” is set to “<NO>,” “ALL CH STEREO”is not available.To cancel Surround/DSP modesTurn MULTI JOG so that “SURROUND OFF” appears on thedisplay.When you select “AUTO SURROUND”You can enjoy the Surround mode easily.• For details about the Surround modes, see page 32.• When “AUTO SURROUND” is activated, the AUTO SURR indicatorlights up on the display.How does “AUTO SURROUND” work?• If a multi-channel signal comes in, an appropriate Surroundmode will be selected automatically.• If a Dolby Digital 2-channel signal with surround signal comesin, “PLII MOVIE” will be selected.• If a Dolby Digital 2-channel signal without surround signalcomes in, “SURROUND OFF (stereo)” will be selected.• If a Linear PCM signal comes in, “SURROUND OFF (stereo)”will be selected.NOTE“AUTO SURROUND” does not take effect in the following cases:– While playing an analog source,– While selecting one of the fixed digital decode mode—“DOLBYDIGITAL” or “DTS” (see page 15).Activating the Surround/DSP modesAvailable Surround/DSP modes vary depending on the speakersettings and the incoming signals. For details, see page 32.Activating one of the Surround/DSP modes automaticallyrecalls the memorized settings and adjustments.• To adjust the speaker output level, see page 24.• When activating one of the Surround/DSP modes, youcan adjust CENTER TONE. (see page 26)• When activating one of the Surround/DSP modes(except Pro Logic IIx Music, Pro Logic II Music, NEO:6Music, and ALL CH STEREO), you can adjust CENTERALIGN. (see page 26)• When activating NEO:6 MUSIC, you can adjust CENTERGAIN. (see page 26)• When activating the DSP mode (except All ChannelStereo mode), you can adjust the following settings:EFFECT (see page 25)LIVENESS (see page 25)ROOM SIZE (see page 25)• When activating “PLIIx MUSIC” and “PLII MUSIC”, youcan adjust the following settings:CENTER WIDTH (see page 26)DIMENSION (see page 26)PANORAMA (see page 25)Selecting the Surround/DSP modesFrom the remote control:1 Select and play any source other than DVDMULTI.• Make sure you have selected the input mode (analog ordigital) correctly.2 Press SURROUND repeatedly to select theSurround/DSP mode you want.Ex.: When “DOLBY DIGITAL” is selected for Dolby Digitalmulti-channel software:*1 “AUTO SURROUND” is the initial setting.*2 Available Surround modes vary depending on the speakersettings and the incoming signals. For details, see page32.*3 If an incoming signal is a multi-channel (more than 2channel) digital signal, “MONO FILM” is not available.*4 If “SURROUND SPK” is set to “<NO>,” “ALL CH STEREO”is not available.To cancel Surround/DSP modesPress SURROUND repeatedly so that “SURROUND OFF”appears on the display.121,32LLS RSS.WFR LFEC RDIGITALDIGITAL AUTOSURROUND OFF (Back to the beginning)Surround modes*2AUTO SURROUND*1HALL1 HALL2 LIVE CLUB DANCE CLUBPAVILION THEATER1 THEATER2MONO FILM*3 ALL CH STEREO*4LLS RSS.WFR LFEC RDIGITALDIGITAL AUTOSURROUND OFF (Back to the beginning)Surround modes*2AUTO SURROUND*1HALL1 HALL2 LIVE CLUB DANCE CLUBPAVILION THEATER1 THEATER2MONO FILM*3 ALL CH STEREO*4