JVC LVT1321-010C Instructions Manual

20In this case, set the distance as follows:Left front speaker (L): “FRONT L <3.0m> (10ft)”Right front speaker (R): “FRONT R <3.0m> (10ft)”Center speaker (C): “CENTER <3.0m> (10ft)”Left surround speaker (LS): “SURR L <2.7m> (9ft)”Right surround speaker (RS): “SURR R <2.7m> (9ft)”Left surround back speaker (SBL) : “SBACK L <2.4m> (8ft)”Right surround back speaker (SBR) : “SBACK R <2.4m> (8ft)”NOTES• You cannot set the speaker distance for the speakers you haveset to “NO.”• If you have selected “< 1SPK>” for “S BACK OUT” (see page19), “S BACK DIST” appears instead of “S BACK L DIST” and“S BACK R DIST.”Setting the speaker distanceThe distance from your listening point to the speakers is one ofthe important elements to obtain the best possible sound effectfrom the Surround/DSP modes.By referring to the speaker distance, the receiver automaticallysets the delay time of the sound through each speaker so thatsounds through all the speakers can reach you at the same time.7 Measuring unit—DIST UNITSelect which measuring unit you use.UNIT <meter> Select to set the distance in meters.UNIT <feet> Select to set the distance in feet.Initial setting: UNIT <meter >7 Speaker distance—FRONT L DIST (for the left front speaker),FRONT R DIST (for the right front speaker),CENTER DIST (for the center speaker),SURR L DIST (for the left surround speaker),SURR R DIST (for the right surround speaker),S BACK L DIST (for the left surround back speaker),S BACK R DIST (for the right surround back speaker)Adjustable range: 0.3 m to 9.0 m in 0.3 m intervals(1 ft to 30 ft in 1 ft intervals)Initial setting: 3.0 m (10 ft) for all speakersActivating the EX/ES/PLIIx setting—EX/ES/PLIIxDepending on this setting, available Surround modes for digitalmulti-channel software vary—EX/ES/PLIIx (7.1-channel)reproduction or 5.1-channel reproduction. Select an appropriatesetting for your enjoyment.• For details about relation between EX/ES/PLIIx setting andavailable Surround mode, see page 32.• To activate the Surround mode, see page 33.<AUTO> According to the incoming signal, an appropriateSurround mode is applied.• For Dolby Digital Surround EX and DTS-ESsoftware, 6.1-channel reproduction is applied*.• For other multi-channel (more than 4 channel)encoded software, 5.1-channel reproduction isapplied.<ON> Select to apply 6.1-channel reproduction to both5.1-channel and 6.1-channel encoded software.<PLIIx MOVIE> Select to apply PLIIx MOVIE (7.1-channel)reproduction to both 5.1-channel and 6.1-channel encoded software.<PLIIx MUSIC> Select to apply PLIIx MUSIC (7.1-channel)reproduction to both 5.1-channel and 6.1-channel encoded software.<OFF> Select to cancel the EX/ES/PLIIx (7.1-channel)reproduction.Initial setting: < AUTO >* For some Dolby Digital Surround EX software, Dolby Digital 5.1-channel reproduction (“DOLBY DIGITAL”) may be applied eventhough you have selected “< AUTO >”. In this case, select“< ON>” to apply “DOLBY D EX.”From the remote control:Press EX/ES/PLIIx repeatedly to select either one of theabove.NOTES• This function is not available- when “SURROUND SPK” is set to “NO” (see page 19) or- when “DVD MULTI” is selected as the source.• When “S BACK SPK” is set to “NO” (see page 19), the VirtualSurround Back (see page 32) is applied for EX/ES/PLIIx (6.1-channel) reproduction.CL RSBLS RSSBL SBR2.1 m(7 ft)2.4 m(8 ft)2.7 m(9 ft)3.0 m(10 ft)3.3 m(11 ft)1 2 34 5 67 8 910 0 10