JVC DR-MV1 Instructions Manual

Also see for DR-MV1: Instructions Instructions

Contents

EN 45OPERATIONS ON DVD DECKOn-Disc Timer programming is a function used with discs that areespecially intended for a specific programme. The disc is thenprogrammed for a programme you always watch every day orevery week. Since older programmes are automaticallyoverwritten, a single DVD-RAM/RW (VR mode) disc can be usedwithout worrying about how much recording capacity remains.( pg. 46)You can programme each disc to timer-record as many as8 programmes.To Make The Disc For On-Disc Timer Programming1 Load a recordable disc.2 Press VCR/DVD repeatedly so that the DVD lamp lights up onthe unit.3 Press PROG/CHECK to access the Programme Check screen.4 When On-Disc Timer programming is made for the first timeon the discPress rt to select “DISC TIMER PRGM”, then press ENTER.● When some programmes are recorded on the disc, a cautionmessage appears. In such a case, backup the programmes asrequired, then format the disc before making On-Disc Timerprogramming. ( pg. 86)When On-Disc Timer programming has already been made onthe discPress rt to select “NEW TIMER PROGRAMME”, then pressENTER.5 Press rt to set the desired date.● The current date appears on the TV screen. The date you enterappears in its place.6 Press w e to select “START”, then press rt to set the desiredstart time.● Each press of rt advances/goes back the start time in 1-min.increments.● To advance/go back the start time in 30-min. increments, press andhold rt.7 Press w e to select “STOP”, then press rt to set the desiredstop time.● Each press of rt advances/goes back the stop time in 1-min.increments.● To advance/go back the stop time in 30-min. increments, press andhold rt.8 Press w e to select “TV PROG”, then press rt to select thedesired channel.9 Set “DAILY/WEEKLY” option.● Refer to step 6 in “SHOWV IEW®Timer Programming” ( pg. 43).● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timerprogramming. ( pg. 43, “Daily/Weekly Recording”)10 Set the other recording options as required.● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.However, you cannot select FR (JUST), FR60–FR360 and FR420.● Refer to step 6 in “SHOWV IEW®Timer Programming” ( pg. 43).● It is not possible to use the Free Rate function. ( pg. 42)11 Press ENTER to access the Programme Confirmation screen.12 Press ENTER to complete timer programming.● To programme another timer, repeat steps 3 – 12.To Timer-record The Programme With The ProgrammedDisc1 Load a programmed disc.2 Press DVD TIMER (#). The unit turns off and “ ” appearson the front display panel. The DVD timer lamp also lights up onthe unit and the VCR deck is automatically selected. When theVCR deck is in timer standby mode, the unit is automatically turnedoff.● To disengage the timer mode, press 1 again.NOTES:● Even if On-Disc Timer programming is overlapping with other timerprogramming, any caution message does not appear. In such a case,recording will be executed in the descending order of the recordingstart time of the programme.● On-Disc Timer programming is not possible on a DVD-RW discformatted in video mode. ( pg. 86)● The information of a programme recorded with On-Disc Timerprogramming is not stored in the library. ( pg. 63)● The play list is not created for the programmes recorded with On-DiscTimer programming. ( pg. 60)● S HOW VIEW Timer programming is not possible on the discs usedexclusively for On-Disc Timer programming.● Manual Timer programming is not possible on the On-Disc TimerProgrammed disc. ( pg. 44)● Basic Recording is not possible on the On-Disc Timer Programmeddisc. ( pg. 40)● The On-Disc Timer programming function does not work on the unitform other manufactures even if the On-Disc Timer Programmed discis loaded.● The beginning of a programme may not be recorded. Also, if the 1stprogramme’s recording stop time and the 2nd programme’s recordingstart time is the same, the ending of the 1st programme may not berecorded.● If there is a power cut while recording, the recordings before thepower cut are not guaranteed.On-Disc Timer Programming● Make sure that the unit’s built-in clock is set properly.● Turn on the unit.● Turn on the TV and select the AV mode.● Slide the TV/CABLE/SAT/DVD switch to DVD.ATTENTION:● On-Disc Timer programming is possible only with the disc for On-Disc Timer programming.● If data is recorded on a disc for On-Disc Timer programming usinga unit from another manufacturer, On-Disc Timer programmingmay no longer function properly.1472580369PROG/CHECKENTERDVD TIMER (#)rtw eVCR/DVD 1SATSatellite Receiver UsersTo timer-record a satellite broadcast using the On-Disc Timerprogramming function:A Perform “Satellite Receiver Control Setting” ( pg. 21).B Perform “On-Disc Timer Programming” ( pg. 45). Instep 10, you cannot set “VPS/PDC” to “ON”.C Leave the satellite receiver’s power on.Downloaded From DvDPlayer-Manual.com JVC Manuals