JVC DR-M10 Instructions Manual

Also see for DR-M10: Instructions Instructions Instructions Instructions

Contents

Masterpage:Right-No-HeadingEN 31Filename [DR-M10SE_07Playback.fm]Page 31 March 4, 2004 2:55 pmHigh-Speed SearchDuring playback, press 5 for forward high-speedsearch, or 3 for reverse high-speed search.● Each press of the button increases the search speed for eachdirection.● To resume normal playback, press 4.ORDuring playback, press and hold 6 for 2 or moreseconds for forward high-speed search, or press and hold2 for 2 or more seconds for reverse high-speed search.● Releasing the button resumes normal playback.Still Picture/Frame-By-FramePlayback1 Pause during playback.Press 9.2 Activate frame-by-frame playback.Press 9.● Each press of 9 advances the still picture frame by frame.ORPress w e.● Each press of w e advances/reverses the still picture frame byframe.● Frame-by-frame playback for reverse direction cannot beperformed with Video CD/SVCD discs.● To resume normal playback, press 4.Slow MotionWhile paused, press SLOW – or SLOW +.● Each press of SLOW – or SLOW + increases the slow motionspeed for each direction (from 1/16 to 1/2 times the normalspeed).● Slow motion for reverse direction cannot be performed withVideo CD/SVCD discs.ORPress 2 or 6 for 2 or more seconds.Skip SearchDuring playback, press .● Each press initiates an approximately 30-second period of fast-motion playback. Normal playback resumes automatically.Resume FunctionIt is possible to memorise the position where you stop playbackand resume playback from that position.● Be sure to set “RESUME” to “ON” or “DISC RESUME”.( pg. 96)1 Memorize a resume point.Press 8 during playback.● The unit enters Resume Stop mode and memorises theposition where you have stopped playback as a resume point.(The inside of the disc status indicator on the front displaypanel blinks in the Resume Stop mode.)● The unit retains a memory of the resume points of the last 30discs played back, even though they have been ejected if“RESUME” is set to “DISC RESUME”. ( pg. 96)● To clear the resume points:(The inside of the disc status indicator stops blinking andlights.)When “RESUME” is set to “ON”:• Press 1 on the unit or DVD1 on the remote control toturn off the unit.• Press x to take out the disc.• Press 8 in stop mode.• Press TOP MENU to display the top menu, then startplayback by selecting an item, etc.• Press MENU to display the disc menu, then start playback byselecting an item, etc.When “RESUME” is set to “DISC RESUME”:• Set “RESUME” to “OFF”. ( pg. 96)• Press 8 in stop mode.• Press TOP MENU to display the top menu, then startplayback by selecting an item, etc.• Press MENU to display the disc menu, then start playback byselecting an item, etc.2 Resume playback.Press 4 in stop mode. The unit starts playback from theresume point.NOTES:● “DISC RESUME” setting works on DVD VIDEO, VCD, SVCDand already finalised DVD-R/DVD-RW (video mode) discs. Forother types of discs, the function under “ON” setting will beapplied even if “RESUME” is set to “DISC RESUME”.● If you stop the playback of a disc for which an resume pointhas already been memorized, the memory will be updatedwith the new resume point.● After the unit has memorized the resume point for 30 discs,remembering a new resume point will cause the unit to deletethe oldest memorized point. Stopping playback of a disc forwhich a resume point is already stored may change the orderin which the points are stored. This may potentially change theorder in which points are deleted.● When the unit memorizes a resume point for a disc, it alsoremembers audio language, subtitle and angle settings.● This function may not work for some Video CD or SVCD.● When “RESUME” is changed to “ON” or “OFF”, resumepoints of the discs memorized with “RESUME” set to “DISCRESUME” will be cleared.● Resume points are memorized for each side of a double-sideddisc.DR-M10SE_07Playback.fm Page 31 Thursday, March 4, 2004 2:56 PM