OneStart

Menu

Handcell DAG1000 Series User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Equipment Introduction
  4. power supply
  5. Voice and Fax parameters
  6. call hold
  7. Call Transfer
  8. way Conference
  9. Factory Reset
  10. Sending and Receiving Fax
  11. WEB Configuration
  12. Login WEB
  13. State and Statistics
  14. Registration Information
  15. Quick Setup Wizard
  16. VLAN Parameter
  17. Static Route Table
  18. SIP Server
  19. Port Configuration
  20. Advanced
  21. Media Parameter
  22. SIP Parameter
  23. Digit Map
  24. Feature Codec
  25. System Parameter
  26. Call & Routing
  27. IP Trunk
  28. Routing Configuration
  29. Tel-IP/Tel Routing
  30. Manipulation Configuration
  31. Tel-IP Caller
  32. Tel-IP Callee
  33. Firmware Upload
  34. Data Backup
  35. Tracert Test
  36. Password Modification
  37. Device Restart
  38. Glossary
Handcell DAG1000 Series User Manual Manual pdf 51 page image
DAG1000/2000 Series FXS Voice Gateway User Manual482) Fill IP address or domain connected, click start.3) Received a message indicates that network connection normal, or network connected to afault.Figure 4.11-5 Ping Parameter Interface4.11.6 Tracert TestTracert is trace router and used to tracking routing.Tracert sends a sequence of Internet Control Message Protocol (ICMP) echo request packetsaddressed to a destination host. Determining the intermediate routers traversed involvesadjusting the time-to-live (TTL), aka hop limit, Internet Protocol parameter. Frequently startingwith a value like 128 (Windows) or 64 (Linux), routers decrement this and discard a packetwhen the TTL value has reached zero, returning the ICMP error message ICMP Time Exceeded.Tracert works by increasing the TTL value of each successive set of packets sent. The first set ofpackets sent have a hop limit value of 1, expecting that they are not forwarded by the firstrouter. The next set have a hop limit value of 2, so that the second router will send the errorreply. This continues until the destination host receives the packets and returns an ICMP EchoReply message.Trace route uses the returned ICMP messages to produce a list of hops (which usually consists
/ 54
This manual is suitable for:
DAG1000 SeriesDAG2000 Series
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved