OneStart

Menu

Handcell DAG1000 Series User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Equipment Introduction
  4. power supply
  5. Voice and Fax parameters
  6. call hold
  7. Call Transfer
  8. way Conference
  9. Factory Reset
  10. Sending and Receiving Fax
  11. WEB Configuration
  12. Login WEB
  13. State and Statistics
  14. Registration Information
  15. Quick Setup Wizard
  16. VLAN Parameter
  17. Static Route Table
  18. SIP Server
  19. Port Configuration
  20. Advanced
  21. Media Parameter
  22. SIP Parameter
  23. Digit Map
  24. Feature Codec
  25. System Parameter
  26. Call & Routing
  27. IP Trunk
  28. Routing Configuration
  29. Tel-IP/Tel Routing
  30. Manipulation Configuration
  31. Tel-IP Caller
  32. Tel-IP Callee
  33. Firmware Upload
  34. Data Backup
  35. Tracert Test
  36. Password Modification
  37. Device Restart
  38. Glossary
Handcell DAG1000 Series User Manual Manual pdf 31 page image
DAG1000/2000 Series FXS Voice Gateway User Manual28Send CID before Ringing After enable this configuration, The DAG send caller to phone set beforeringing, otherwise the caller ID will display after ringing.Delay of sending CID afterRingingDefinite delay timer of caller ID while it set to send caller ID after ringing.Its Default value 500msSLIC Setting Set the unit impedance4.8.2 Media ParameterMedia parameter mainly include: RTP start port, DTMF parameter, Prefered Vocoder.Configuration Interface as follow：Figure 4.8-2 Media Parameter Configuration InterfaceMedia parameter description:RTP Start Port Default RTP port 8000DTMF Method SINGAL、INBAND、RFC2833RFC2833 Payload Type OptimizationIt is configurable When RFC2833 is selected,payload negotiation parameter with remote side, itincludes two options: Local and remoteRFC2833 Payload Type Payload value, default is 101DTMF Gain Default is 0 DBDTMF Send Interval DTMF send signal interval, default is 200ms.Coder NameDAG supports G729、G711U、G711A、G723. whileit make outgoing call, G.729 will used as figure4.8.2 displayed
/ 54
This manual is suitable for:
DAG1000 SeriesDAG2000 Series
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved