0 Copyright Fujitsu Technology Solutions, Release September 2011ETERNUS DX60 S2Hardware and Software InstallationHardware and Software Installation ETERNUS DX60 S2

Fujitsu ETERNUS DX60 S2 Hardware And Software Installation Manual

naming conventions

Chapter 1 Workflow

Chapter 2 Checking the Server Environment

VERITAS Cluster Server (VCS)

Chapter 3 Notes

Fibre Channel Card Notes

VERITAS Volume Manager (VxVM) Notes

Chapter 4 Installing and Setting Up ETERNUSmgr

Chapter 5 Setting Up the ETERNUS DX Disk Storage System

Chapter 6 Setting Up the Fibre Channel Switches

Chapter 7 Installing Drivers and Setting Up the Server

Chapter 8 Connecting the Server to the ETERNUS DX Disk Storage Systems

Chapter 9 Setting Up the Server to Recognize the Logical Units

For SUSE Linux Enterprise Server

Chapter 10 Setting Up and Checking the Multipath Driver

Chapter 11 Setting a File System

Manager Environment

ETERNUS DX60 S2

For VMware Infrastructure 3

ETERNUS DX Disk Storage System Setup Notes

Jumbo Frame Setting Notes

Chapter 6 Setting Up the VMware ESX Server

Checking the LAN Cards

Creating the Virtual Switches

Setting the Software Initiator

Enabling ALUA

Checking the LUNs

Setting CHAP Authentication

Plug-in Settings

Turning on the Devices

Chapter 7 Virtual Machine

Applying Required Patches

Chapter 8 Dynamic Recognition of LUNs Added While VMware ESX is in Use

LVM Notes

Chapter 4 Checking the Server Information

Chapter 5 Setting Up the ETERNUS DX

Chapter 6 Installing the iSCSI Software Initiator and Setting Up the Server

Setting Up the Server

Maximum Number of Volume Group Settings

Server Settings when CHAP Authentication is Used

Server Settings when Bidirectional CHAP Authentication is Used

Chapter 7 Checking Connections

Multipath Configuration using PV-Links

Multipath Configuration using Native Multipath

Enabling ALUA (alua_enabled)

Fibre Channel Switch Notes

Server Startup and Power Supply Control Notes

Virtual I/O Server (VIOS) Notes

Chapter 5 Installing and Setting Up ETERNUSmgr

Chapter 6 Setting Up the ETERNUS DX/AF

Chapter 7 Setting Up the Fibre Channel Switches

Chapter 8 Installing Drivers and Setting Up the Server

For VIOS/VIOC Configuration

Installing the Multipath Driver

Chapter 9 Checking Connections

Setting Logical Units

Chapter 10 Setting the Multipaths

Chapter 11 Creating the Volumes

Creating the Logical Volumes

Chapter 12 SAN Boot

Chapter 13 Storage Migration

using this manual

compliance with standards

about this manual

symbols used in this manual

safety precautions

power synchronized unit

Chapter 1 Overview

Features

Specifications

Components

Table 1.2 Status and meanings of each LED (for power synchronized units)

AC Sensor Unit (Optional)

System Configuration

Figure 1.6 System configuration example (power synchronization with three or more server UPS units)

Power Management for Power Synchronization

Figure 1.8 Operation timing chart when using a power synchronized unit (powering on)

Figure 1.9 Power off using a power synchronized unit

Figure 1.10 Operation timing chart when using a power synchronized unit (powering off)

Chapter 2 Installation

Preparation

Installing in a Rack

Installing a Power Synchronized Unit

Installing an AC Sensor Unit

Chapter 3 Powering On and Off

Chapter 4 Connection and Settings

Setting the ETERNUS DX/AF

Figure 4.2 ETERNUS DX8700 S3/DX8900 S3 setup (Setup Power Management screen)

Figure 4.3 ETERNUS DX80 S2/DX90 S2 setup (Setup Power Management screen)

Figure 4.4 ETERNUS DX60 S2 setup (Setup Power Management screen)

Turning on the Power Synchronized Unit

Connecting Cascade Cables

Connecting to the Server UPS Unit

Connecting the Server UPS Unit to the Power Synchronized Unit

Connecting the AC Sensor Unit

Connecting to the ETERNUS DX/AF

Checking after Connection

Chapter 5 Adding a Connecting Device

Connection Procedure When Adding an ETERNUS DX/AF

Chapter 6 Operation and Maintenance

Replacing a Power Synchronized Unit

Troubleshooting

Trouble Record

chapter 1 overview

system configuration

flow from installation to operation

chapter 3 configuration

Test

Chapter 4 Operation

Group

Provisioning

Management

performance management

Types

Intervals

Information

Condition

copy table size settings

Copy

Operation

Monitoring

nas management

System

Environment

Volume

Snapshot

Stop/Start

operating environment

Configuration

Server

installation steps

Interface

Method

Folder

Name

Sharing

Snapshot Reference

Capture

Pool

chapter 5 maintenance

5.1.2 Restoring Express's Manager Environment

5.1.3 Changing Express's Manager Environment

5.1.3.2 Changing IP Address

5.2 Maintenance of Express's Manager Environment

5.2.2 Restoring Express's Manager Environment

5.2.3 Changing Express's Manager Environment

5.2.3.2 Changing IP Address

Stopped

Function

A.3.1 How SnapOPC+ Eorks

A.3.2 Restore

A.3.4 SDP operation

Express

B.1 storageadm perfdata (Performance Information Management

B.2 esfsnap (Express's Manager Troubleshooting Information Collection

Index

Chapter 2 Setting Up the ETERNUS DX

Sense Data Conversion (Setting the Host Responses)

Table 2.5 Host response settings

Creating and Allocating LUN Groups (Setting Host Affinity Groups)

Specific Settings

Setting the Subsystem Parameters (for HP-UX only)

Chapter 1 Hardware Configurations

Controllers

Figure 1.12 Host interface port (FC model)

Power Supply Units

Figure 1.18 Rear view of a drive enclosure (single-expander type)

Expanders

Enclosure Connection Path

Disks

Power Distribution Units (Only for Regions Other than EMEA&I)

Figure 1.27 Power distribution unit (AC200-240V, 2U, Max 6 enclosures connection)

provided AC cable specifications

Chapter 2 ETERNUS DX Disk Storage System Installation

Package Size

Installation Area

Installation Environment

Load Bearing Capacity for Floors

Required Number of Outlets/Sockets

Figure 2.3 Power distribution unit (2U)

Circuit Protectors

Breaking Characteristics

Chapter 3 Connections

Host Connection Path

LAN Connection

Power Supply Connection

Figure 3.10 Single-line power supply when connecting to a power socket and a UPS unit

Fujitsu ETERNUS DX60 S2 Hardware And Software Installation Manual

Product

Learn More

Legal