Fanimation The Odyn FPD8148 Owner's Manual

Contents

Fanimation The Odyn FPD8148 Owner's Manual Manual pdf 2 page image

Important Safety InstructionsWARNING: To avoid fire, shock and serious personal injury, follow these instructions.1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assemblydiagrams.2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to preventpower from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten awarning device, such as a tag, to the service panel.3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceilingfan before servicing.4. Do not insert anything into the fan blades while the fan is operating.Additional Safety Instructions1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan withoutblades.2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. Theceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made orapproved by a licensed electrician.3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not toexceed 35 lbs. or 15.88 kgs.). See page 5 of owner’s manual for support requirements. Consult a qualified electrician if indoubt.4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequateelectrical knowledge or experience, have your fan installed by licensed electrician.6. Suitable for use with solid-state speed controls.WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,ISOLATING WALL CONTROL/SWITCH.WARNING: This product is designed to use only those parts supplied with this product and/or accessories designatedspecifically for use with this product. Using parts and/or accessories not designated for use with this product could result inpersonal injury or property damage.WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing theWARNING: Mount to an outlet box marked acceptable for fan support.brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.LIMITED LIFETIME WARRANTYExtends to the original purchaser of a Fanimation Fan1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanshipduring the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defectivefan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costsincurred in the removal or reinstallation and shipping of the product for repairs or replacement.2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, dueto defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national servicecenter. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for allcosts incurred in the removal or reinstallation and shipping of the product for repairs or replacement.3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials orworkmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at ournational service center.4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,corroding, tarnishing, or peeling.5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure toextremes of heat or humidity, or as a result of any modification to the original product.6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store thatsold the fan or Fanimation.7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under thiswarranty.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PCperipheral, then shall include the following or equivalent:Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and the receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.5. The appliance is not intended for use by young children or infirm persons without supervision. Young children should besupervised to ensure that they do not play with the appliance.7. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to agrounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should beconnected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then itshould be connected to an equipment-grounding conductor.