Craftsman 2611650 Quick Setup Manual

Not forReproductionProtect pump from damage caused by freezing, readoperator’s manual for winter or long term storage. Freezedamage is NOT covered under warranty.Copyright © 2018. All rights reserved.Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).WARNING Failure to read and follow theoperator’s manual and all operatinginstructions before using could result indeath or serious injury.WARNING Risk of electrocution. Contactingboth power conductors, at the sametime could cause electric shock or burnresulting in death or serious injury.• Inspect cord before each use, DO NOT use ifcord is damaged.• Keep all connections dry and off the ground.• DO NOT touch plug with wet hands.WARNING High water pressure could cutthrough skin resulting in serious injury.Spray gun traps high water pressure,even when motor is stopped and water isdisconnected. NEVER aim spray gun at people,animals, or plants. ALWAYS point spray gun insafe direction, press red button and squeezetrigger to release high pressure, every time youturn off pressure washer.Items Included• Main unit• Operator’s manual• Spray gun• High pressure hose• Spray wand with Quick Connect (QC)• 7-in-1 nozzle• Red high pressure nozzleYou will need (Not Included)• Garden hose, 15m (50 ft.) or less• Safety goggles (indirect vented type)• Petroleum or synthetic greaseUnpack Electric Pressure Washer1. Remove everything from carton.2. Raise handle (A) to upright position by pulling up latch (B)on each side of handle. Push latches down to secure handlein place. 13. Ensure you have all included items prior to assembly. Ifitems are damaged or missing, call 1-888-331-4569.4. Prior to assembly, lubricate rubber o-ring seals on allconnections with petroleum or synthetic grease. SeeOperator’s Manual, Lubricate O-Rings. 2 3 4 6 7Connect Hoses and Water Supply1. Uncoil high pressure hose and attach black end of hose (C)to base of spray gun (D). Tighten by hand. 22. Attach blue end of high pressure hose (C) to high pressureoutlet (E) on pump. Tighten by hand. 3NOTICE If inlet screen is damaged or missing. DO NOT usepressure washer, call 1-888-331-4569.3. Before connecting garden hose (F) to water inlet (G), inspectinlet screen (H). Clean screen if it contains debris or have itreplaced if damaged. DO NOT run pressure washer if inletscreen is damaged. 44. Run cold water through garden hose (F) for 30 secondsto clean out any debris. Connect the garden hose (notto exceed 50 ft. (15 m) in length) to the water inlet (G).Tighten by hand. 42DCHF G43CE5J6K L7KMN89RSP10Connect Spray Wand and 7-in-1 Nozzle1. Turn ON water, point gun in a safe direction, press triggerlock button (J), then squeeze trigger to purge pump systemand spray gun of air and impurities. 52. Attach spray wand (K) to spray gun (L). Tighten by hand. 63. Pull back on collar of spray wand (K), insert 7-in-1 nozzle(M) and release collar. Tug on 7-in-1 nozzle to make sure itis securely in place. 7NOTICE For nozzle instructions, see Operator’s Manual.NOTICE High water supply pressure may not allow detergent toflow. See Operator’s Manual, Troubleshooting.How to Start Your Electric PressureWasher1. Put on safety goggles.2. Turn on water.NOTICE DO NOT run pump without water supply connected andturned on.NOTICE The unit can be operated in vertical or horizontalpositions.3. Turn master ON/OFF switch (N) to OFF (0) position. 84. Plug electrical power cord into a dedicated electrical circuitrated for 120 Volts AC at 15 Amps that is properly installedin accordance with all local codes and ordinances. Circuit isnot to supply any other electrical needs. 9NOTICE The indicator light must be ON for electric pressurewasher to operate.5. Press TEST button (P). The indicator light (R) should beOFF. 106. Press RESET button (S). The indicator light (R) should beON. 10NOTICE DO NOT use electric pressure washer if above test fails.7. Turn master ON/OFF switch (N) to ON (I) position. 88. Point gun in a safe direction, press trigger lock button (J)and squeeze trigger. 5The electric pressure washer motor will start and stop as spraygun trigger is depressed and released.NOTICE If a fuse blows or circuit breaker trips, motor break inmay be necessary. Run pressure washer in any POWERflow+High Flow Mode ( ) nozzle setting for 10 minutes.How to Stop Your Electric Pressure WasherNOTICE To ensure detergent tank does not drain during storage,empty after each use, see operator’s manual.The electric pressure washer motor runs only when the trigger isengaged. To stop the electric pressure washer and turn off themotor:1. Release spray gun trigger.2. Turn master ON/OFF switch (N) to OFF (0) position. 8NOTICE Releasing trigger will shut off motor but does not shutoff electrical power to unit.3. Turn off water supply.4. ALWAYS point spray gun in a safe direction and squeezespray gun trigger to relieve built up pressure in unit.NOTICE Spray gun traps high water pressure, even when motoris stopped and water is disconnected.5. Disconnect GFCI plug from outlet. 96. For storage instructions, see Operator’s Manual.WARNING Risk of electrocution. Use of an extension cordcould cause electric shock or burn resulting in deathor serious injury.• DO NOT use an extension cord with this electric pressurewasher. Your home’s electrical circuit receptacle or extensioncord may not provide lifesaving ground-fault circuit-interruption protection.WARNING Risk of electrocution. Non-operating ground faultcircuit interrupter (GFCI) could result in death orserious injury. If indicator light does not stay on aftertest and reset, do not use GFCI.WARNING Risk of eye injury. Spray could splash back orpropel objects resulting in serious injury. Alwayswear indirect vented (chemical splash) safety gogglesmarked to comply with ANSI Z87.1 when using or invicinity of this equipment. NEVER substitute safety glasses ordry-condition goggles for indirect vented safety goggles.1BAB80029109 Rev. AQuick Setup GuideElectric Pressure WasherHave Questions?Do not return to store. We can help.Call Customer Service Toll-Free 1-888-331-4569or visit our website, www.Craftsman.com

/ 2

Related manuals for Craftsman 2611650