OneStart

Menu
Craftsman 108.27807 Operator's Manual Manual pdf 70 page image

Craftsman 108.27807 Operator's Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 previewPage 65 previewPage 66 previewPage 67 previewPage 68 previewPage 69 previewPage 70 previewPage 71 previewPage 72 previewPage 73 previewPage 74 previewPage 75 previewPage 76 previewPage 77 previewPage 78 previewPage 79 previewPage 80 preview
Contents
  1. Table Of Contents
  2. Introduction
  3. Understanding Warnings
  4. Safety Warnings
  5. Warning Decals
  6. emission control information
  7. Daily Pre-Ride Inspection
  8. Operation Warnings
  9. Vehicle Identification
  10. Basic System Functions
  11. throttle lever
  12. setting the parking brake
  13. engine cooling system
  14. oil system
  15. Starting the Engine
  16. Vehicle Break-in Period
  17. Riding
  18. traveling uphill
  19. side hilling
  20. turning around on a hill
  21. trail obstacles
  22. parking on an incline
  23. Carrying Loads
  24. CVT System
  25. Battery
  26. replenishing the battery fluid
  27. Exhaust System
  28. Maintenance
  29. lubrication recommendations
  30. handlebar adjustment
  31. front wheel hub tightening
  32. steering inspection
  33. front brake
  34. spark plugs
  35. radiator coolant level inspection
  36. rear gear case
  37. wheel installation
  38. indicator lamp replacement
  39. Storage
  40. Troubleshooting
  41. Tools
  42. System Specifications
  43. Wiring Diagram
Craftsman 108.27807 Operator's Manual Manual pdf 70 page image
70Wheel Removal Procedure1. Stop the engine, place the transmission in gear and lock the parking brake.2. Loosen the wheel nuts slightly.3. Elevate the side of the vehicle by placing a suitable stand under the footrestframe. The stand must be sturdy enough to safely support the weight of theATV.4. Remove the wheel nuts and remove the wheel.Wheel Installation1. With the transmission in gear and the parking brake locked, place the wheel inthe correct position on the wheel hub. Be sure the valve stem is toward theoutside and rotation arrows on the tire point toward correct rotation.2. Attach the wheel nuts and finger tighten them.3. Lower the vehicle to the ground.4. Securely tighten the wheel nuts according to the specifications in the chartbelow.Bolt Size SpecificationFrontM10 X 1.25 20Ft.Lbs 27N.mRearM12 X 1.25 50Ft.Lbs 69N.mTire Inspection &ReplacementAlways replace tires when treaddepth (1) is worn to 1/8˝ (3mm) or less.When replacing tires always useoriginal equipment size and type. SeeSection 21 “Specifications – DriveSystem” for tire sizes.
/ 80
This manual is suitable for:
108.27807
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved