Canon PIXMA iP3500 Series Easy Setup Instructions

Also see for iP3500 - PIXMA Color Inkjet Printer: Supplementary guide Quick start guide Quick start guide Quick start guide Quick start guide

Contents

Canon PIXMA iP3500 Series Easy Setup Instructions Manual pdf 1 page image

Start HereEasy Setup Instructions Photo PrinterUnpack the Printer Please confirm the included items against the illustration printed on the lid of the packing box or in the Quick Start Guide.A USB cable is necessary to connect the printer with your computer.••1 Prepare the Printera Place the printer on a flat andhorizontal surface, and do not placeany objects in front of the printer.Open the Rear Tray and extend the PaperSupport. Open the Front Tray, and extend theOutput Tray Extension.CautionBefore turning on the printer, remove all the ship-ping tapes.b Plug the power cord in the back of theprinter and connect the other end to thewall outlet.ImportantDo not connect the USB cable until after thesoftware is installed.Plug the power cord all the way in, since it maybe difficult to plug.c Press the POWER button to turn on theprinter.d Open the Top Cover. The Print HeadHolder moves to the center.Top Cover••a Remove the Print Head from itspackage.CautionThere may be some transparent or light blue inkon the inside of the bag the print head comes in,or the inside of the protective cap - this has noeffect on print quality. Be careful not to get ink onyourself when handling these items.b Remove the orange protective cap fromthe Print Head and discard it.Protective CapPrint Head NozzlesElectrical ContactsNoteDo not touch the print head nozzles and the electricalcontacts.c Firmly raise the Print Head Lock Leveruntil it stops. The Print Head LockLever may feel heavy.d Insert the Print Head.Do not touch!e Push the Print Head to hold it in place,and lower the Print Head Lock Levercarefully.ImportantIf the Top Cover is left open for more than 10minutes, the Print Head Holder moves to the right.Close and reopen the Top Cover to return theHolder to the center.f Make sure that the Print Head isinstalled correctly.ImportantBe sure that the Print Head Lock Lever is pressedall the way down, and that the Print Head is lockedfirmly in place. If the Print Head is tilted forward, orthe Print Head Lock Lever is pressed only halfwaydown, raise the Print Head Lock Lever and removethe Print head, and then reinstall the Print Head.3 Install the Ink TanksNoteFor the ink tanks compatible with this printer, refer tothe back cover of the Quick Start Guide.a Pull the orange tape in the direction ofthe arrow to peel off the protective filmand remove the film completely.If the air hole is blocked with the remaining film, inkmay leak out or may not eject properly.b Twist off and discard the orangeprotective cap located on the bottom ofthe ink tank.Protective CapDo not press!Electrical ContactsInk PortImportantDo not touch the electrical contacts.Do not touch the ink port.c Insert the ink tank into the right-handslot and press the mark on the inktank until it clicks into place.d Make sure the ink lamp lights red.Install all ink tanks in orderfrom right to left accordingto the colored label.••e Close the Top Cover.ImportantThe printer starts operating. Wait about 2 min-utes until the printer stops making noise.When printing for the first or second time aftersetup, the print will take a minute or two before itbecomes ready to print.NoteIf the ALARM lamp on the printer flashes orange afteryou have closed the Top Cover, refer to “ALARM LampFlashes Orange” in “Troubleshooting” of the QuickStart Guide.Hardware setup is complete.••ImportantWhen cleaning the exterior of the printer, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Printer” in the Quick Start Guide.2 Install the Print HeadLoading PaperThis printer offers two paper sources to loadprinting paper; the Rear Tray, found at the topof the printer, and the Front Tray, found at thefront of the printer.NoteAt purchase, the printer is set to feed from theRear Tray. If you are printing without changingpaper source settings, load paper in the RearTray. For details on how to change the papersource, refer to “Printing from Your Computer” ofthe Quick Start Guide.You cannot load paper other than A4, Letter,or B5-sized plain paper (such as Canon SuperWhite Paper SW-201) in the Front Tray. Whenusing any other type of paper, load it in the RearTray.Rear TrayFront TrayLoading Paper in the Rear Traya Load the paper into the Rear Traywith the print side facing UP.b Align the paper stack against theCover Guide on the right side ofthe Paper Support.c Pinch the Paper Guide and slideit against the left side of the paperstack.NoteMake sure that the Cover Guide is set uprightwhen you load paper in the Rear Tray.Paper GuidePrint sidefacing UP.Cover GuideLoading Paper in the Front Traya Load the paper into the Front Traywith the print side facing DOWNand the leading edge to the farside.b Align the right edge of the paperstack against the inner face of theFront Tray.c Align the near and left edges ofthe paper stack with the PaperSize Mark.d Pinch the Paper Guide and slide ituntil it lightly touches the left sideof the loaded paper stack.ImportantIf the Paper Guide is pressed too firmlyagainst the side of the loaded paper, thepaper may bend and not feed properly.Paper GuidePrint side facing DOWN.NoteFor details, refer to the Quick Start Guide.••

/ 2

Related manuals for Canon iP3500 - PIXMA Color Inkjet Printer