OneStart

Menu

Adaptec AAA-133U2 - AAA 133 RAID Controller Hardware Manual

Also see for AAA-130U2 SERIES: Installation and hardware guide

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Page 69 preview
Page 70 preview
Page 71 preview
Page 72 preview
Page 73 preview
Page 74 preview
Page 75 preview
Page 76 preview
Page 77 preview
Page 78 preview
Page 79 preview
Page 80 preview
Page 81 preview
Page 82 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. obtaining scsi cables
  4. System Requirements
  5. system requirements
  6. installation overview
  7. installing the hardware
  8. AAA-131U2/133U2 RAID Card Layout
  9. Installing DIMM Memory
  10. Installing the AAA-131U2/133U2
  11. Connecting the LED Activity Indicator
  12. Setting Up SCSI Devices
  13. Terminate the Ends
  14. Additional Hints for Connecting SCSI Devices
  15. Connecting SCSI Devices
  16. Internal Ultra2 SCSI Connector (68-pin)
  17. Internal Ultra SCSI Connector (50-pin)
  18. External Ultra2 SCSI Connector (68-pin)
  19. External SCSI Array Enclosures (Storage Subsystems)
  20. Configuring the AAA-131U2/133U2
  21. Creating an Array
  22. Creating an Array with Custom Setup
  23. Making the Array Bootable
  24. installing the software
  25. Installing the Array1000U2 Driver for Windows NT
  26. Installing the Driver When Windows NT is Already Installed
  27. Windows NT Installation and Configuration Notes
  28. Installing the Array1000U2 Driver for Novell NetWare
  29. Installing the Driver When NetWare is Already Installed
  30. Netware Installation and Configuration Notes
  31. Installing the Array1000U2 Driver for UnixWare
  32. Installing the Driver When Installing SCO UnixWare
  33. SCSISelect Default Settings
  34. Starting the SCSISelect Utility
  35. Using the SCSI Disk Utilities
  36. SCSISelect Settings
  37. Additional Options
  38. Troubleshooting Checklist
  39. Windows NT Troubleshooting
  40. Using a CD-ROM Drive with DOS
  41. External Cables
  42. External Connector Diagrams
Adaptec AAA-133U2 - AAA 133 RAID Controller Hardware Manual Manual pdf 60 page image
6-2AAA-130U2 Series Installation and Hardware GuideInstalling the Array1000U2 Driver for UnixWareTo begin driver installation, see either Installing the Driver WhenInstalling SCO UnixWare below, or Installing the Driver When SCOUnixWare is Already Installed on page 6-3.Installing the Driver When Installing SCO UnixWareTo install thecda1000 driver at the same time you install SCOUnixWare, follow the instructions below:1 Insert the SCO UnixWare Installation disk in the floppy bootdrive. Reboot your computer.Wait for the first SCO UnixWare installation screen and promptto appear, then follow the onscreen instructions.2 When prompted to Install HBA Diskette, first remove theInstallation disk, then insert the Adaptec Array1000U2 FamilyManager Set driver disk for SCO UnixWare into your floppydisk drive.3 Select Install HBA Diskette and press F10.4 If you have additional HBA disks, insert the next HBA disk,select Install HBA Diskette and press F10.If all of your HBA disks have been installed, select ProceedWith Installation and press F10. (Do not reinstall thecda1000HBA disk.)5 If necessary, enter the DCU (Device Configuration Utility) toview/change the SCO UnixWare device driver configurationdata; otherwise select Continue With Installation.6 When prompted, reinsert the HBA disk (Adaptec Array1000U2Family Manager Set driver disk for SCO UnixWare) that youinserted in Step 3 above, and press Enter.7 Follow the onscreen instructions to complete the installation.Note: If your installation fails, do not attempt to use theupdate installation pkgadd procedure to fix the installation.Follow the instructions in the SCO UnixWare documenta-tion and in this document to retry the installation.
/ 82
Related manuals for Adaptec AAA-130U2 SERIES
Adaptec NCLV-DS User Manual first page preview
Adaptec NCLV-DS User Manual
Adaptec APD-2940UW User Manual first page preview
Adaptec APD-2940UW User Manual
Adaptec LSM-FC2002 Installation Manual first page preview
Adaptec LSM-FC2002 Installation Manual
This manual is suitable for:
AAA-130U2 SERIESAAA-133U2
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved