Absolute Process Instruments APD 7010 Quick Start Manual

Absolute Process Instruments APD 7010 Quick Start Manual Manual pdf 1 page image

Frequency to DC Transmitters, Isolated, Factory Configured APD 7010Input: 0-25 Hz to 0-20 kHzOutput: 0-1 V to 0-10 VDC, ±1 VDC to ±10 VDC, 0-1 mA to 20 mADCO Precision Frequency to DC ConverterO Zero and Span Output Calibration PotentiometersO Full 1200 V Input/Output/Power IsolationO Input and Output LoopTracker®LEDsO Output Test ButtonO Built-In Loop Power Supply for Sink/Source OutputQ Monitor and Control Motor or Line SpeedQ Convert Speed and Frequency SignalsQ Simplify Interfacing of Frequency SensorsApplicationsOptions–add to end of model numberM01 Input/output reversal, such as 20-4 mA outputM09 High voltage output up to 20 V (specify range)U Conformal coating for moisture resistanceAccessory—order as separate line itemAPI BP4 Spare removable 4 terminal plug, blackModel Input Output PowerAPD 7010 Factory ranged0-25 Hz to 0-20 kHzFactory rangedvoltage or milliamps85-265 VAC or 60-300 VDCAPD 7010 D 9-30 VDC or 10-32 VACDescriptionThe APD 7010 accepts a frequency input and provides anoptically isolated DC voltage or current analog output that islinearly proportional to the input.The full 3-way (input, output, power) isolation betweeninput and output makes this module useful for ground loopelimination, common mode signal rejection, and noise pickupreduction.Also standard on the APD 7010 is a 15 VDC input excitationsupply. If needed, this supply can be used to power a passivesensor, eliminating the need for an additional external powersupply.Common applications include frequency to DC conversionsfrom frequency output type devices such as rotary encoders,magnetic pick-ups, variable speed drives and flow meters.A PLC pulse rate output can be programmed to vary. By con-necting the APD 7010 to this output, a proportional analogsignal can be generated.Sink/Source VersatilityFor maximum versatility the output can be selectively wired forsinking (unpowered) or sourcing (powered) milliamp output.The 20 VDC loop excitation supply can be used to power amilliamp current loop if required. The output can also be wiredfor an externally powered loop.LoopTrackerAPI exclusive features include two LoopTracker LEDs (green forinput, red for output) that vary in intensity with changes in theprocess input and output signals. These provide a quick visualpicture of your process loop at all times and can greatly aid insaving time during initial startup and/or troubleshooting.Output TestAn API exclusive feature includes the test button to provide afixed output (independent of the input) when held depressed.The test output level is potentiometer adjustable 100% of theoutput span.The output test button greatly aids in saving time during initialstartup and/or troubleshooting.All models are factory configured.Order APD 7010 D for operation on low voltage powerMilliamp outputs can be field wired for sink or source.How to OrderPlease specifyModelInput range in HzOutput rangeOptions as requiredFrequency Input RangeFactory configured, please specify input rangeFrequency: 0-25 Hz to 0-20 kHzSine wave, sawtooth, or square wave with min. 5 μsec pulseInput Amplitude Range100 mV to 150 VRMSAny waveform with minimum 100 mV amplitude changeInput Impedance10 kW nominal (maximum sensitivity)100 kW nominal (minimum sensitivity)Input Sensitivity/HysteresisMulti-turn potentiometer for sensitivity adjustmentMaximum sensitivity: ±25 mV typicalMinimum sensitivity: ±2.5 V typicalInput ProtectionNormal mode: 200% of input ratingCommon mode: 600 VDC or 600 VACp input to groundInput Power Supply15 VDC ±10%, regulated, 25 mADCMax. ripple, less than 10 mVRMSMay be used to power sensorLoopTrackerVariable brightness LEDs indicate I/O loop level and statusDC Output RangeFactory configured, please specify output rangeVoltage: 0-1 VDC to 0-10 VDCVoltage, M09 option: 0-10 VDC to 0-20 VDCBipolar voltage: ±1 VDC to ±10 VDCCurrent: 0-2 mADC to 0-20 mADC20 V compliance, 1000 W at 20 mAOutput CalibrationMulti-turn zero and span potentiometers, ±15% adj. range typ.Output Loop Power Supply20 VDC nominal, regulated, 25 mADCMax. ripple, less than 10 mVRMSMay be selectively wired for sinking or sourcing mA outputOutput Test/OverrideFront momentary button or external contact closure sets out-put to test level. Potentiometer adjustable 0-100% of span.Output Ripple and NoiseLess than 10 mVRMS ripple and noiseLinearityBetter than ±0.1% of spanAmbient Temperature Range and Stability–10°C to +60°C operating ambientBetter than ±0.02% of span per °C stabilityIsolation1200 VRMS minimumFull isolation: power to input, power to output, input to outputHousing and ConnectorsIP 40, requires installation in panel or enclosureFor use in Pollution Degree 2 EnvironmentMount vertically to a 35 mm DIN railFour 4-terminal removable connectors, 14 AWG max wire sizePower85-265 VAC, 50/60 Hz or 60-300 VDC, 2.5 W maximumD versions: 9-30 VDC or 10-32 VAC 50/60 Hz, 2.5 W max.Dimensions0.89" W x 4.62" H x 4.81" D22.5 mm W x 117 mm H x 122 mm DHeight includes connectors15 VDC SensorPower AvailableInput LoopTrackerLEDOutput LoopTrackerLEDAdjustable OutputTest FunctionConnect mA Outputfor Sink or SourceUniversalPowerZero and Span forOutputRemovable PlugsAdjustable InputSensitivity© 02-20api-usa.com1220 American Way Libertyville, IL 60048Phone: 800-942-0315 Fax: 800-949-7502AABSOLUTEBSOLUTE PPROCESSROCESS IINSTRUMENTSNSTRUMENTS1 2 3 45 6 7 89 10 11 1213 14 15 16See WiringDiagrams onNext PageQuick Link: api-usa.com/7010Free FactoryI/O Setup!H H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HMade in USAFile E14596885-265 VAC, 60-300 VDCmodel onlyApplications Linkapi-usa.com/appsPb LeadFree

/ 2

Related manuals for Absolute Process Instruments APD 7010