Absolute Process Instruments APD 6010 Quick Start Manual

Absolute Process Instruments APD 6010 Quick Start Manual Manual pdf 1 page image

AC to DC Transmitters, Isolated, Factory Configured APD 6010Input: True RMS 0-50 mVAC to 0-300 VAC, 0-1 mAAC to 0-1000 mAACOutput: 0-1 V to 0-10 VDC, ±5 VDC, ±10 VDC, 0-1 mA to 0-20 mADC, 4-20 mADCO Full 1200 V Input/Output/Power IsolationO Zero and Span Output Calibration PotentiometersO Input and Output LoopTracker®LEDsO Functional Test Button with Remote CapabilityO Built-In Loop Power Supply for Sink/Source OutputQ Convert an AC Signal to a DC Process SignalQ Monitor Voltage RangesQ Convert, Amplify Low Level AC SignalsApplicationsOptions–add to end of model numberM01 Output reversal, such as 20-4 mA outputM09 High voltage output up to 20 V (specify range)U Conformal coating for moisture resistanceAccessory—order as separate line itemAPI BP4 Spare removable 4 terminal plug, blackModel Input Output PowerAPD 6010 Factory configured—specifymVAC, VAC, or mAAC rangeFactory configured—specifyVDC or mADC range85-265 VAC or 60-300 VDCAPD 6010 D 9-30 VDC or 10-32 VACDescriptionThe APD 6010 accepts an AC voltage or current input andprovides an optically isolated DC voltage or current outputthat is linearly related to the input. Typical applications includemonitoring line, power supply, shunt, and motor voltages orcurrent (either directly or with a current transducer) for control,preventive maintenance, etc.The full 3-way (input, output, power) isolation makes this mod-ule useful for ground loop elimination or noise pickup reduc-tion. The APD 6010 is factory configured to customer require-ments. Consult the factory for assistance with special ranges.Sink/Source Output VersatilityFor maximum versatility a milliamp output can be selectivelywired for sinking or sourcing. This allows the APD 6010 mil-liamp output to connect to a powered or unpowered currentloop. The 20 VDC output loop supply can be used to power apassive mA device if required.LoopTrackerAPI exclusive features include two LoopTracker LEDs (green forinput, red for output) that vary in intensity with changes in theprocess input and output signals. These provide a quick visualpicture of your process loop at all times and can greatly aid insaving time during initial startup and/or troubleshooting.Functional TestAn API exclusive feature includes the Functional Test Buttonto provide a fixed output (independent of the input) when helddepressed. The test output level is potentiometer adjustablefrom 0 to 100% of output span. The functional test buttongreatly aids in saving time during initial startup and/or trouble-shooting.The functional test can also be enabled with a customer-supplied external contact closure across terminals 5 and 6.This allows remote testing of the output or, for example, aPLC-controlled manual override setting.All models are factory ranged. Please specifyModel APD 6010 orAPD 6010 D for operation on low voltage powerOrder options and accessories as requiredHow to OrderI/O are factory set to your specifications. Please provideInput rangeOutput rangeOptions as requiredAC Input RangeFactory configured, please specify input rangeConsult factory for special rangesVoltage: 0-50 mVAC to 0-300 VACCurrent: 0-1 mAAC to 0-1000 mAACMeasurements are true RMSInput Impedance (Voltage Input)220 kΩ minimumInput Voltage Burden (Current Input)1.0 VRMS maximumInput Frequency40 Hz to 1000 Hz sinusoidalInput Protection, Common Mode750 VDC or 750 VACpCommon Mode Rejection120 dB minimumLoopTrackerVariable brightness LEDs indicate I/O loop level and statusDC Output RangesFactory configured, please specify input rangeConsult factory for special rangesVoltage: 0-1 VDC to 0-10 VDC, 10 mA maxVoltage, M09 option: 0-10 VDC to 0-20 VDCBipolar voltage: ±1 VDC to ±10 VDCCurrent: 0-1 mADC to 0-20 mADC20 V compliance, 1000 Ω at 20 mAOutput CalibrationMulti-turn zero and span potentiometers±15% of span adjustment range typicalOutput Loop Power Supply20 VDC nominal, regulated, 25 mADCMax. ripple, less than 10 mVRMSMay be selectively wired for sinking or sourcing mA outputOutput Test/OverrideFront momentary button or external contact closure sets out-put to test level. Potentiometer adjustable 0-100% of span.Output Ripple and NoiseLess than 10 mVRMS at 40 Hz and aboveLinearityBetter than ±0.1% of spanAmbient Temperature Range and Stability–10°C to +60°C operating ambientBetter than ±0.02% of span per °C stabilityResponse Time150 milliseconds nominal (0-90%)Isolation1200 VRMS minimumFull isolation: power to input, power to output, input to outputHousing and ConnectorsIP 40, requires installation in panel or enclosureFor use in Pollution Degree 2 EnvironmentMount vertically to a 35 mm DIN railFour 4-terminal removable connectors, 14 AWG max wire sizePower85-265 VAC, 50/60 Hz or 60-300 VDC, 2 W maximumD versions: 9-30 VDC or 10-32 VAC 50/60 Hz, 2 W maximumDimensions0.89" W x 4.62" H x 4.81" D22.5 mm W x 117 mm H x 122 mm DHeight includes connectorsConnect mA Outputfor Sink or SourceOutput LoopTrackerLEDInput LoopTrackerLEDCustom InputRangesUniversalPowerZero and Span forOutputRemovable PlugsAdjustable OutputTest/OverrideFunctionCustom OutputRanges© 11-19api-usa.com1220 American Way Libertyville, IL 60048Phone: 800-942-0315 Fax: 800-949-7502AABSOLUTEBSOLUTE PPROCESSROCESS IINSTRUMENTSNSTRUMENTS1 2 3 45 6 7 89 10 11 1213 14 15 16See WiringDiagrams onNext PageQuick Link: api-usa.com/6010Free FactoryI/O Setup!H H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HMade in USAFile E14596885-265 VAC, 60-300 VDCmodel onlyApplications Linkapi-usa.com/appsPb LeadFree

/ 2

Related manuals for Absolute Process Instruments APD 6010