OneStart

Menu

ABB XFC G5 manuals

XFC G5 first page preview

XFC G5

Brand: ABB | Category: Controller
XFC G5 first page preview

XFC G5

Brand: ABB | Category: Remote Control
Table of contents
  1. Table Of Contents
  2. Table Of Contents
  3. Cyber security
  4. Additional information
  5. Safety
  6. Potential safety hazards
  7. Compliance
  8. Considerations before installation
  9. Site planning and requirements
  10. Wiring requirements
  11. Basic hardware installation
  12. Unpack and inspect
  13. Pipe mount installation
  14. Wall-mount installation
  15. Direct-mount installation
  16. Ground equipment
  17. Install and connect the RTD for the XFC
  18. Install antenna (for wireless functionality)
  19. Install battery and charger
  20. Install the solar panel
  21. Wire COMM ports
  22. XRC COMM pinouts
  23. Wire I/O
  24. Digital input and output (DI/DO) pinouts
  25. Powering the device
  26. Power with battery and charger
  27. Connect the charger
  28. Power with external power supply
  29. Enable real time clock backup
  30. Local communication with the device
  31. Establish connection with the XFC or XRC
  32. Change to Expert view
  33. Configure the basic parameters
  34. Change the default time and date format
  35. Initial measurement application setup
  36. Configure communications
  37. Configure COMM2
  38. Configure for network communication
  39. Enable and configure Ethernet
  40. Enable Wi-Fi
  41. Enable Bluetooth
  42. Configure basic security (recommended)
  43. Commission the device
  44. Optional volume reset (recommended)
  45. Troubleshooting
  46. Failure to start
  47. Remote communication failure
  48. Contact us
XFC G5 first page preview

XFC G5

Brand: ABB | Category: Measuring Instruments
Table of contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Table Of Contents
  7. Table Of Contents
  8. Table Of Contents
  9. Additional information
  10. Safety
  11. System Description
  12. Operating system
  13. Table 1-2: XFC G5 applications
  14. Log period data records
  15. Display application
  16. Configuration files
  17. Customer data collection files
  18. Enclosures
  19. Electronic board
  20. Table 1-6: Local communication ports/wireless support (local operator access)
  21. Table 1-8: Network connection (Ethernet)
  22. Battery and charger power configurations
  23. Site planning and requirements
  24. Install PCCU
  25. Installation
  26. Direct-mount installation
  27. Overview
  28. Termination panel
  29. Figure 3-4: 6990 Rack mount enclosure
  30. Install the RTD
  31. Figure 3-6: Typical RTD installation
  32. Install battery and charger
  33. Figure 4-1: Solar panel
  34. Wire COMM ports
  35. Figure 5-1: XFC G5 R-232 COMM1
  36. Figure 5-2: XFC G5 R-232 COMM2
  37. Figure 5-3: XFC G5 R-485 COMM1
  38. Figure 5-5: XRC RS-232 COMM 1
  39. Figure 5-6: XRC RS-485 COMM 1
  40. Wire I/O
  41. Analog inputs (AI)
  42. Digital outputs (DO)
  43. Figure 6-2: XRC AI terminals and input mode selector jumpers
  44. Figure 6-4: XRC DI/PI/DO terminals, input mode switches, and debounce jumpers
  45. Powering the Device
  46. Connect the battery (dc power)
  47. Figure 7-4: XFC G5 charger connection
  48. Figure 7-6: Battery and switch
  49. Basic configuration and startup
  50. Figure 8-1: System Setup
  51. Figure 8-3: PCCU32 Date/Time synchronization warning
  52. Station setup
  53. Figure 8-7: Station Setup detail
  54. Figure 8-8: Flow Measurement Advanced Setup (Gas orifice)
  55. Configure COM1
  56. Figure 8-11: XFC G5 COMM terminals (Module in COMM1 slot shown)
  57. Figure 8-13: Verify the communications set up for COMM1
  58. Configure COM2
  59. Configure for network communication
  60. Enable Wi-Fi
  61. Figure 8-17: Wi-Fi tab screen
  62. Enable Bluetooth
  63. Figure 8-19: Enable Bluetooth
  64. Figure 8-21: Add/Assign Bluetooth application to Bluetooth interface
  65. Validate the device measurement
  66. Optional volume reset (recommended)
  67. Configure security (recommended)
  68. Open Transmission Control Protocol (TCP) ports
  69. Denial of service (DOS) thresholds rates
  70. Figure 9-2: S1 Security switch
  71. Default access roles
  72. Figure 9-4: Security Editor screen
  73. Edit the security file
  74. Enable RBAC authentication on communication ports
  75. Use default RBAC credentials
  76. Figure 9-9: Login dialog box
  77. Supported SSH/SFTP accounts
  78. Update default SSH/SFTP keys
  79. Figure 9-11: Puttygen Key Generator
  80. Figure 9-13: New public key
  81. Figure 9-14: New private key and passphrase
  82. Figure 9-16: Select location to save private key file
  83. Figure 9-18: Copy generated public key
  84. Figure 9-19: Enable the SSH/SFTP service
  85. Figure 9-21: FileZilla Site Manager connection setup
  86. Figure 9-22: Type private key passphrase (password)
  87. Figure 9-24: Open the /Flash/AppData/.ssh/ directory
  88. Figure 9-27: Restart Totalflow device after public key update
  89. Service and maintenance
  90. Save the device configuration
  91. Figure 10-2: Station Setup and Backup
  92. Figure 10-3: 32Bit Loader confirmation pop-up
  93. Figure 10-5: Save Software from Device window
  94. Figure 10-7: Select location to save config file
  95. Backward or forward clock change not crossing an hour boundary
  96. Warm restart with onboard RESET button
  97. Warm restart from the device loader
  98. Warm restart from PCCU entry mode
  99. Warm restart using terminal mode
  100. Cold restart from the device loader
  101. Cold restart from terminal mode
  102. Restart using the factory configuration
  103. Remove power from the electronic board
  104. Reconnect power to the electronic board
  105. Replace the 12 Vdc battery
  106. Replace the lithium battery
  107. Replace the LCD assembly
  108. Figure 10-24: XFC G5 Display connector
  109. Replace or add communication modules (COMM modules)
  110. Calibration
  111. Differential pressure checks
  112. Figure 11-2: DP calibration pressure checks
  113. Calibrating static pressure
  114. Calibrating differential pressure (DP)
  115. Zero transducer
  116. Static pressure
  117. Table 11-2: RTD wiring pinouts
  118. Table 11-3: AI calibration points
  119. Analog input calibration
  120. Analog input calibration (voltage mode)
  121. Figure 11-6: AI voltage default calibration values
  122. Analog input calibration (current mode)
  123. Figure 11-9: AI current default calibration values
  124. Verify analog input calibration
  125. Repeat calibration in case of errors
  126. Troubleshooting
  127. Table 12-2: Typographical of conventions
  128. Contact us
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved