OneStart

Menu

Z-BEAST 54ZB Owner's Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Contents
  1. Table Of Contents
  2. Safety Information and Warnings
  3. Inspection and Serial Number Locations
  4. Preparation Safety Precautions
  5. Operation Safety Precautions
  7. Roll Over Protective Structure (ROPS)
  8. Slope Diagram
  9. Safety Decals
  10. Product Specifications
  11. Control Panel and Lawn Mower Components
  12. Missing Parts Request Form
  13. Operating Instructions
  14. Operating the Mower
  15. Disengaging Hydraulic Drive Units
  16. General Maintenance
  17. Maintenance Schedule
  18. Service Adjustments
  19. Removing the Blades
  20. Engine-to-Hydraulic Drives Belt Adjustment
  21. Hydraulic Drive System Adjustment
  22. Safety System Adjustment
  23. Lubrication
  24. Storage Instructions
  25. Troubleshooting
  27. Limited Warranty and Service
Z-BEAST 54ZB Owner's Manual Manual pdf 30 page image
2654ZB, 62ZBZ- Beast Finish MowerRev: AUG2014Z- BEAST Service AdjustmentsSafety System AdjustmentsWARNING: Do not bypass, modify, alter, ordisconnect the safety system. Make sure that thesafety interlock system is fully operational each timebefore mowing. Failure to do so could present dangerto you and others around you.There are generally three (3) ways to adjust thesensitivity of a safety switch. The most appropriate wayto adjust each switch depends upon the application,location, and the nature of the problem you areencountering.Method 1: Adjust location using the mountingscrews1. Move the blade control lever to OFF.2. Loosen screws (A) until safety switch (B) movesfreely.3. Slide safety switch (B) firmly against blade bellcrank (C).4. Tighten screws (A) and check that safety switch (B)does not move.Method 2: Adjust location using adjustment nuts onswitch body1. Loosen locking nut (C) on the sensor shaft.2. Adjust switch location by turning the nuts.3. Tighten the locking nut when proper adjustment isachieved.WARNINGACBTracking AdjustmentsWARNING! ALLOW THE MUFFLER TO COOL BEFOREMAKING THIS ADJUSTMENT! This adjustment is madein close proximity to the muffler. The muffler on canreach extremely hot temperatures and can burn youinstantly on contact.For mowers with serial numbers 54ZB13XXXX and62ZB13XXXX:1. Loosen the jam nut on the control rod on the side that ismoving slower.2. Turn the control rod one turn clockwise while facingthe rear of the mower.3. Tighten the jam nut.4. Drive mower in straight line and adjust again ifnecessary.For mowers with all other serial numbers:Remove pin and turn adjuster one turn at a time untilmower tracks straight.WARNINGLoosenjam nut Turn controlrod with fingersTurn clockwise to increaseright side speedTurn counter clockwise toincrease left side speed
/ 35
Related manuals for Z-BEAST 54ZB
Z-BEAST FINISH MOWER 48ZB Owner's Manual first page preview
Z-BEAST FINISH MOWER 48ZB Owner's Manual
This manual is suitable for:
54ZB62ZB
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved