U-Line 2115R Service Manual

Also see for 2175DWRR: Use and care guide Specifications Supplementary guide Installation guide Use and care guide

Contents

U-Line 2115R Service Manual Manual pdf 76 page image

3-61Section 3 - Service and Repair9. Unplug unit power cord from electrical outlet.10. Reinstall back panel.To connect to drain:1. Attach the 5/8" ID drain connection on the back of the unit to a5/8" OD rigid tube, using a worm clamp.2. Attach the other end of the rigid tube to your 5/8" ID drain linewith a worm clamp.3. Insulate the drain line, if necessary, to prevent condensation.LOCALLY-INSTALLED DRAIN PUMPIf a gravity drain connection is not possible, and you have notpurchased the CLR2160 with factory-installed pump, we stronglyrecommend the use of the U-Line P60 drain pump. The U-Line P60drain pump is available through your dealer, or direct from U-Linewith complete installation instructions. If a pump other than the U-Line P60 drain pump is to be used, it must meet the followingspecifications:• It must be UL listed and have a UL listed, 120 VAC,3-wire grounded power cord.• It must have overall maximum outside dimensions of8-3/4" wide x 5-3/4" deep x 7-3/4" high.• It must have a minimum flow rate of 15 gallons per hour at 10 feetof lift.• It must have a sealed sump which does not allow water leakage inthe case of a power outage, restricted drain or pump failure.• It must have a check valve in the discharge line to prevent wastewater return to the pump.• It must have an overflow protection control which will shut offpower to the ice maker in the event of a pump failure.• It must have an operating temperature range of 50°F to 110°F(10°C to 40°C).U-CLR DRAIN KIT (AVAILABLE FOR PURCHASE)Tools Required• 1/4" Nut driver or flat 5/16" screwdriver• Side cutter• Copper tubing cutter• 12" Level• 9/16" Open end wrench• 7/16" Open end wrench• PliersMaterials Required• (10' or more depending on water supply location) 1/4" O.D. softcopper tubing• **(10' or more depending on drain location) 5/8" I.D. braidreinforced PVC drain tubing• **(3) 11/16" to 1-1/4" Clamp range worm drive hose clamps• **(1) Brass garden hose fitting (supplied with product)• **(1) Nylon barbed coupling for 5/8" ID hose• **(1) 5/8" to 7/8" adapter** Depending on your model, your unit may have been packaged withthese items. If you need to order these items, please contact U-Line andorder Part # U-CLRDRAINKIT.NOTE: These instructions are based on the U-Line recommendations andcommon industry practice. You must consult your local plumbing codes toensure compliance. U-Line requires the use of copper cold water supplyconnection tubing. Plastic tubing should not be used.1. Locate the desired cold water supply location. Attach a 1/4"copper line to this location and route the tubing to the appliance.Leave approximately 8' of water line to be coiled behind theappliance as shown (Figure 69). This water line should belooped into 2 coils. This will allow the line to flex when movingthe appliance in and out of the opening.Figure 692. Locate the U-Line supplied garden hose fitting. Ensure the end ofthe copper tubing has been cut straight and is free of burrs. Slidethe compression nut and ferrule onto the copper tubing as shown(Figure 70). Push the assembly completely into the garden hosefitting and tighten using the two wrenches. Wait to connect thisassembly to the appliance until the drain connection is ready.ULIN_S_165