SIPROCESS GA700Continuous Gas AnalyticsSIPROCESS GA700 rack and wallmounted devicesCompact Operating Instructions7MB3000-.....-....7MB3010-.....-.... 7MB3017-.....-....7MB3020-.....-.... 7MB3027-.....-....7MB3040-.....-.... 7MB3047-.....-....06/2023A5E35134047-ABIntroduction 1Safety notes 2Installing/mounting 3Connecting 4Commissioning 5Service and maintenance 6Technical data 7Product documentationand support AEx px safety equipment BEx pz safety equipment C

Siemens SIPROCESS GA700 Compact Operating Instructions

SIPROCESS GA700

Introduction

General safety instructions

Installing

Wall-mounted device

Installing the rack-mounted device

Connecting

Connection of the signal lines

Electrical connections, pin assignment

Electrical connections/terminal assignment

Gas connections

Optional purging gas connections (wall-mounted device)

Leak test

Operation

Menu structure

Commissioning

Commissioning the SIPROCESS GA700

Maintenance & diagnostics > Identification

Identifying a device

Identifying an analyzer module

Identifying additional features

Safety

Settings > Time/date

Settings > Measuring ranges

Setting the measuring ranges

Setting Autoranging

Digital inputs

Setting digital inputs

Digital outputs

Functions

Setting digital outputs

Setting functions/components of a digital output

Settings > Gas path/process tag label

Settings > Calibrations

Sequence of a calibration/validation

Setpoints, tolerances, flow time

Setting the setpoints

Setting validation tolerances

Setting the calibration tolerances

Setting the sample gas purging time

Carry out calibrations

A.1 References

Index

Laws and directives

Qualified personnel

Description

Design

Nameplate layout

OXYMAT 7

Design of module nameplate

Important features

Functional principles

Reference gas monitoring, OXYMAT 7

Application planning

Operation with at least one OXYMAT 7

Installing the analyzer modules and option module

Installation of the analyzer modules

Figure 5-4 Connection between terminal block and OM2.1

Installing the option module OM 2.1

Figure 5-6 Installation of option module OM 2.1

Cabling

Installing the device

Connection to electricity supply

Figure 7-1 Electrical connection

Figure 7-3 Pin assignment of standard terminal block, terminal rows C and D

Purging gas connections (optional)

General information

Zero point error

Introducing reference gas

Checking the sample gas path for leaks

Maintenance and servicing

Notes on maintenance

Figure 10-1 Unlocking the connector for equipotential bonding

Figure 10-2 Replacing seals

Replace basic device

Replacing the processing unit

Figure 10-4 Replacing the processing unit

Replacing the cable gland set

Errors

Return procedure

Technical specifications

OXYMAT 7 technical specifications

Dimension drawings

Spare parts/accessories

Spare parts list OXYMAT 7

A.1 Certificate

A.3 Technical support

B.1 ESD Guidelines

C.1 Abbreviations

Glossary

Purpose of this document

History

Notes on warranty

Environmentally friendly use of resources

Conventions

Proper use

Prerequisites for safe use

Device modifications

Conformity with European directives

Automatic reset

Overview

Rack-mounted housing

Device/module identification

Principle of operation of OXYMAT 7

Reference gas monitoring OXYMAT 7

Reference gas monitoring with pressure switch

ULTRAMAT 7

How the ULTRAMAT 7 works

Reference gas monitoring

CALOMAT 7

How the CALOMAT 7 works

Combined operation

Operating modes

Operating modes: Selection of operating mode

Sample gas restrictors/clamping screws

Conditions for use/installation

Plug & measure permitted activities

Setting instructions

Case differentiations

Option modules

Table 4-1 Installation conditions for the sample gas restrictor

Operation with at least one ULTRAMAT 7

Operation with at least one CALOMAT 7

Dispose of sample gas through an exhaust gas line

Installing/removing modules in the rack-mounted enclosure

Rack-mounted housing tool

Cables

Installing/removing analyzer modules

Installation of the analyzer module

Wiring OXYMAT 7

Connecting the ULTRAMAT 7

Connecting CALOMAT 7

Removing an analyzer module

Installing option modules

Wiring option modules

Figure 7-4 Pin assignment of optional module 1.1

Figure 7-5 Pin assignment of optional module 2.1

Spark suppression: Example

Installation/removal of restrictors

Gas preparation

Introduction of reference gas

Checking the reference gas flow

Interference gases/zero point error

Sample gas inlet conditions

Maintenance and service

Cleaning the device

Replacing option modules

Technical specifications of rack-mounted housing

Technical specifications of analyzer modules

Table 11-10 OXYMAT 7: Time response

Table 11-12 OXYMAT 7: Influence variables

Technical data ULTRAMAT 7

Table 11-17 ULTRAMAT 7: Measuring ranges

Table 11-21 ULTRAMAT 7: Influence variables

CALOMAT 7 technical specifications

Table 11-31 CALOMAT 7: Measuring response

Table 11-33 CALOMAT 7: Climatic conditions

A5E35134047

Sicherheitshinweise

Historie

Technische Daten

Hinweis zur Industriellen Nutzung

Anwendungsbereich

Lieferung

Transport und Lagerung

Hinweise zur Gewährleistung

Voraussetzungen für den sicheren Einsatz

Konformität mit europäischen Richtlinien

Unsachgemäße Änderungen am Gerät

Anforderungen an besondere Einsatzfälle

Einsatz in explosionsgefährdeten Bereichen

Allgemeine Bestimmungen zum Explosionsschutz

Innerer Explosionsschutz

Gerätevarianten Ex px mit ständiger Durchspülung bzw. Ex pz mit Nutzung des Containment Systems

Automatisches Reset

Grundlegende Sicherheitshinweise

Anforderungen an den Einbauort

Sachgemäße Montage

Sicherheitshinweise zur Installation

Wandgerät

Einschubgerät installieren

Wandgerät installieren

Demontage

Anschließen

Elektrische Anschlüsse

Einschubgerät

Stromversorgung anschließen

Anschluss der Signalleitungen

Gasanschlüsse

Spülgasanschlüsse am Wandgerät

Anschlusspläne für die Varianten Ex px bzw. Ex pz mit "ständiger Durchspülung

Siemens SIPROCESS GA700 Compact Operating Instructions

Product

Learn More

Legal