Maxum Edition IIPD PA APInstallation ManualInstallation ManualGeneral guidelines for receiving, unpacking, andinstalling the Maxum Edition II gas chromatograph.General initial startup procedures are given. Actualpractice is application dependent.12/20192000595 Rev 1Installation Overview 1Safety notes 2Installation Steps 3Initial Startup Procedures 4Appendix A - PECM LEDInterpretation AAppendix B - Change Log B

Siemens Maxum Edition II Installation Manual

Introduction

Analyzer Specific Documents

Isothermal Oven

Switching and Sampling Valves

Operator Controls

Power Supplies

Replacement Procedure

Power Entry and Control Module

Feature Additions

PECM Functions

Oven Temperature Control

Communication and Power Distribution

Onboard Solid State Relays

Oven Functions

Electronic Enclosure Environment

Removing The PECM

Installing The New PECM

Description

Mechanical

SYSCON2.1 Components

CAC3 Status Indicator LEDs

Ethernet Port Expansion

Maintenance Overview

Replacing the Lithium Battery on the SYSCON Module Introduction

Analog and Digital IO

IO Card Common Features

Digital IO Card

Analog IO Board

Analog and Digital IO Board

Detector Personality Modules

Replacing a Base3DPM

Intrinsically-Safe Thermal Conductivity DPM (IS-TCD3)

Replacing an IS-TCD DPM

Replacing a TC-DPM

Sensor Near Electronics (SNE) Software

Solid State Relay Module

Solenoid Valves

Replacing a Solenoid Valve

Electronic Pressure Control Module

Replacing an EPC Module

Color Touchscreen

Replacement Procedures

Specifications

Index

Maxum II

Detector Overview

Thermal Conductivity Detector

Intrinsically Safe Thermal Conductivity DPM

Replacing TCD Components

Procedure to Replace Thermistor Beads

TCD Specifications

Flame Photometric Detector

Upgrade Description

Procedure - Upgrade FPDI to FPDII

Base3 Detector Personality Module (DPM)

Base3DPM Status Indicator LEDs

FPD Specifications

Flame Ionization Detector

FID Maintenance Considerations

Purge Coil and Filter

Procedure to Replace Mesh Filter

Replacing the FID Quartz Jet

Replacing the FID Igniter

Procedure - Removing the Detector

Procedure - Igniter Replacement

Procedure - Reinstalling the Detector

FID Specifications

Filament Detector

Replacing the Filaments

Methanator

Purged Methanator

Explosion-Proof Methanator

Methanator Maintenance Considerations

Air Treater

Air Treater Specifications

Valco Pulse Discharge Detector

Safety notes

Qualified Personnel

System Functions

Functions

Analyzer Operation

Data Communication

General Maintenance and Troubleshooting

LED States Inside the Electronics Cabinet

SIB3 LEDs

PECM LEDs

Modular Oven Model PECM-DC LED Locations

General Analyzer Shutdown Procedure

Procedure

Accessing the Bootloader

Alarm Codes, Descriptions, and Suggested Actions

Alarms 330 through 359 SNE Communication

Alarms 360 - 399

Alarms 400 - 562

Alarms 671 - 699

Alarms 700 - 737

Alarms 801 - 999

Alarms 1002 - 1128

Alarms 1317 - 1319

Alarms 1617 - 1697 Pecm Errors

Alarms 1917 - 2005 DPM TCD

Alarms 2217 - 2306 DPM FID

Alarms 2500 - 2577 Access Bus Driver Errors

Alarms 2817 - 2904 DPM Temperature

Alarms 3117 - 3204 EPC

Alarms 3401 - 3454 TFTP

Alarms 3500 - 3528 Advance

Alarms 3718 - 3804 SNE I/O

Alarms 4001 - 4124 EZChrom

Alarms 4217 - 4320 CAN Bridge

Alarms 4525 - 5220 Advance TC

Alarms 10000 - 11536 MicroSAM

Siemens Maxum Edition II Installation Manual

Product

Learn More

Legal