Sharp EL-1607P Operation Manual

Also see for EL-1607P: Brochure & specs Operation manual Operation manual Operation manual Service manual

To insure trouble-free operation of your SHARP calculator, werecommend the following:1. The calculator should be kept in areas free from extremetemperature changes, moisture, and dust.2. A soft, dry cloth should be used to clean the calculator. Donot use solvents or a wet cloth.3. Since this product is not waterproof, do not use it or store itwhere fluids, for example water, can splash onto it.Raindrops, water spray, juice, coffee, steam, perspiration,etc. will also cause malfunction.4. If service should be required, use only a SHARP servicingdealer, a SHARP approved service facility or SHARP repairservice.5. Do not wind the AC cord around the body or otherwiseforcibly bend or twist it.6. Unplug the calculator by pulling on the plug portion, not thecord.7. Do not place objects on the AC cord. Do not run the AC cordunder rugs, mats, or other such objects.8. This product, including accessories, may change due toupgrading without prior notice.SHARP will not be liable nor responsible for any incidental orconsequential economic or property damage caused bymisuse and/or malfunctions of this product and itsperipherals, unless such liability is acknowledged by law.OPERATIONAL NOTES“OFF”: Power off.“•”: Power ON. Set to the non-print mode.“P”: Power ON. Set to the print mode.“P•IC”: Power ON. Set to the print and item count mode.For addition or subtraction, each time is pressed, 1 isadded to the item counter, and each time is pressed,1 is subtracted.• The count is printed when the calculated result isobtained.• Pressing of , , or clears the counter.Note: The counter has a maximum capacity of 3 digits (up to±999). If the count exceeds the maximum, the counterwill recount from zero.DECIMAL SELECTOR:Presets the number of decimal places in the answer. In the ‘‘F’’position, the answer is displayed in the floating decimal system.CONSTANT/ADD MODE SELECTOR:‘‘K’’: The following constant functions will be performed:Multiplication:The calculator will automatically remember the first numberentered (the multiplicand) and instruction.Division:The calculator will automatically remember the second numberentered (the divisor) and instruction.‘‘•’’: Neutral‘‘A’’: Use of the Add mode permits addition and subtraction ofnumbers without an entry of the decimal point. When theAdd mode is activated, the decimal point is automaticallypositioned according to the decimal selector setting.POWER SWITCH; PRINT / ITEMCOUNT MODE SELECTOR:OPERATING CONTROLSPAPER FEED KEYLAST DIGIT CORRECTION KEYGRAND TOTAL KEYCLEAR ENTRY KEYTOTAL KEYMULTIPLICATION KEYDIVISION KEYMINUS EQUAL KEYPLUS EQUAL KEYCHANGE SIGN KEYMARKUP KEYMEMORY TOTAL CLEAR KEYMEMORY SUBTOTAL RECALL KEYTAX-INCLUDING KEYPRE-TAX KEYPERCENT KEYNON-ADD/SUBTOTAL KEY:Non-add –When this key is pressed right after an entry of anumber in the Print mode, the entry is printed onthe left-hand side with the symbol “#”.Never insert paper roll if torn. Doing so will cause paper tojam.Always cut leading edge with scissors first.1) Insert the leading edge of the paper roll into the opening.(Fig. 1)2) Turn the power on and feed the paper by pressing . (Fig. 2)3) Lift the attached metal paper holder up and insert the paperroll to the paper holder. (Fig. 3)PAPER ROLL REPLACEMENTThere are several situations which will cause an overflow or anerror condition. When this occurs, “E” will be displayed. Thecontents of the memory at the time of the error are retained.If an ‘‘0•E’’ is displayed at the time of the error, must be usedto clear the calculator. If an ‘‘E’’ with any numerals except zero isdisplayed, the error may be cleared with or and thecalculation can still be continued.Also, in rare cases, printing may stop midway and the indication“E” appear on the display. This is not a malfunction but iscaused when the calculator is exposed to strongelectromagnetic noise or static electricity from an externalsource. Should this occur, press the key and then repeat thecalculation from the beginning.Error conditions:1. Entry of more than 12 digits or 11 decimals. This error can becleared with or .2. When the integer portion of an answer exceeds 12 digits.3. When the integer portion of the contents of the memory orgrand total memory exceeds 12 digits.(Ex. 999999999999 1 )4. When any number is divided by zero.(Ex. 5 0 )SPECIFICATIONSWARNINGTHE VOLTAGE USED MUST BE THE SAME AS SPECIFIEDON THIS CALCULATOR. USING THIS CALCULATOR WITHA HIGHER VOLTAGE THAN THAT WHICH IS SPECIFIED ISDANGEROUS AND MAY RESULT IN A FIRE OR OTHERTYPE OF ACCIDENT CAUSING DAMAGE. WE ARE NOTRESPONSIBLE FOR ANY DAMAGE RESULTING FROMUSE OF THIS CALCULATOR WITH A VOLTAGE OTHERTHAN THAT WHICH IS SPECIFIED.In case of abnormal conditionsWhen this unit is exposed to strong RF noise and/or extremephysical shock during the operation, or when the power cord isplugged into the AC outlet, the unit may start functioningabnormally which, in some rare occasions, all keys - including thepower key and the key - cease to respond.If such abnormal conditions are observed, unplug the AC cordfrom the socket. Keep the unit unplugged for about 5 seconds,reconnect the AC plug, then turn on the power.Operating capacity: 12 digitsPower source: AC: 230V-240V, 50HzPRINTING SECTIONPrinter: Mechanical printerPrinting speed: Approx. 2.5 lines/sec.(At temperature 25°C (77°F), when“741•9 +” is printed. The printing speed will vary with thenumber of rows and the figure types to be printed.)Printing paper:57 mm(2-1/4") - 58 mm(2-9/32") wide80 mm(3-5/32") in diameter (max.)Operating temperature:0°C – 40°C (32°F – 104°F)Power consumption: 59 mADimensions:220 mm (W) × 303 mm (D) × 71.5 mm (H)(8-21/32" (W) × 11-15/16" (D) × 2-13/16" (H))Weight: Approx. 1.2 kg (2.65 Ib.)Accessories:1 paper roll, 1 ink roller (installed), and operation manualUse of , and will automatically override the Add modeand decimally correct answers will be printed at the preset decimalposition.ROUNDING SELECTOR:“ ”: An answer is rounded up.“5/4”: An answer is rounded off.“ ”: An answer is rounded down.Note: The decimal point floats during successive calculation bythe use of or .If the decimal selector is set to “F” then the answer is alwaysrounded down ( ).GRAND TOTAL MODE SELECTOR:“GT”: Grand Total“•”: NeutralSTORE KEY:This key is used to store the conversion rate or the tax/discount rate.Conversion rate:• Enter the conversion rate, then press .• A maximum of 6 digits can be stored (decimal point is notcounted as a digit).Tax/discount rate:• Enter the adding tax rate, then press .• To store a discount rate, press before pressing.• A maximum of 4 digits can be stored (decimal point is notcounted as a digit).Note: • For the conversion rate and the tax/discount rate, asingle value can be stored for each. If you enter a newrate, the previous rate will be cleared.• The stored values for the conversion rate and the tax/discount rate will be cleared if the power cable isdisconnected.EL-1607PELECTRONIC PRINTING CALCULATOROPERATION MANUALIf printing is blurry even when the ink roller is in the properposition, replace the roller.Ink roller: Type EA-772RWARNINGAPPLYING INK TO WORN INK ROLLER OR USE OFUNAPPROVED INK ROLLER MAY CAUSE SERIOUSDAMAGE TO PRINTER.1) Set the power switch to OFF.2) Remove the printer cover. (Fig. 1)3) Hold the top of the ink roller and remove the roller by pulling ittoward you and then upward. (Fig. 2)4) Install the new ink roller in the correct position. Make surethat the roller is securely in place. (Fig. 3)5) Put back the printer cover.ERRORSEL-1607P(AB1)-1➀Fig. 2Fig. 3Fig. 1Cleaning the printing mechanismIf the print becomes dull after long time usage, clean theprinting wheel according to the following procedures:1) Remove the printer cover and the ink roller.2) Install the paper roll and feed it until it comes out of the frontof the printing mechanism.3) Hold a small brush (like a tooth brush) lightly to the printingwheel and clean it by pressing .4) Put back the ink roller and the printer cover.Note: Do not rotate the printing mechanism manually, this maydamage the printer.INK ROLLER REPLACEMENTDISPLAY SYMBOLS:M : A number has been stored in memory.– : The display value is negative.E : Error or overflow of capacity.• : Appears when a number is in the grand total memory.This key is used to print out numbers notsubjects to calculation such as code, date, etc.Subtotal –Used to get subtotal(s) of additions and/orsubtractions. When pressed following the orkey, the subtotal is printed with the symbol“◊” and the calculation may be continued.By pressing this key even in the Non-print mode, thedisplayed number is printed without any symbol.CONVERSION KEY:This key is used:• to store the conversion rate.• obtains a value by multiplying a given number with aspecified conversion rate.• to recall the presently stored rate for check. Pressfirst to clear the calculation register and reset anerror condition, then press . The conversion rate isprinted with the symbol “∆”.CONVERSION KEY:This key is used to obtain a value by dividing a givennumber with a specified conversion rate.Fig. 1Fig. 2Fig. 3DO NOT PULL PAPER BACKWARDS AS THIS MAYCAUSE DAMAGE TO PRINTING MECHANISM.PRINTED IN CHINA12DT(TINSE1648EHZZ)12.5.31, 6:17 PMPage 1

/ 2

Related manuals for Sharp EL-1607P