Sharp AL-2020 Service Manual

Also see for AL-2020: Online manual Operation manual Leaflet Service manual

Contents

AL-2020/2035/2040/2050/2060 FAX SOFT SWITCH 12 - 31SW102 No.5–No.8 Scan effective image area main scanright edge image loss (OC)Used to set image loss in scan image area.Image loss on the right edge in OC main scan direction can beadjusted. When the set value is increased, image loss is increased.Setting is made in binary input in the increment of 24 dots.Default: 96 dotsSW103 No.1–No.4 Scan effective image area sub scanlead edge image loss (OC)Used to set image loss in scan image area.Image loss on the lead edge in OC sub scan direction can beadjusted. When the set value is increased, image loss is increased.Setting is made in binary input in the increment of 16 lines.Default: 96 linesSW103 No.5–No.8 Scan effective image area sub scanrear edge image loss (OC)Used to set image loss in scan image area.Image loss on the rear edge in OC sub scan direction can beadjusted. When the set value is increased, image loss is increased.Setting is made in binary input in the increment of 16 lines.Default: 144 linesSW104 No.1–No.4 Scan effective image area main scanleft edge image loss (RSPF back surface)Used to set image loss in scan image area.Image loss in RSPF back surface main scan direction can beadjusted. When the set value is increased, image loss is increased.Setting is made in binary input in the increment of 24 dots.Default: 96 dotsSW104 No.5–No.8 Scan effective image area main scanright edge image loss (RSPF back surface)Used to set image loss in scan image area.Image loss on the right edge in RSPF back surface main scan direc-tion can be adjusted. When the set value is increased, image loss isincreased.Setting is made in binary input in the increment of 24 dots.Default: 96 dotsSW105 No.1 Scan magnification ratio adjustment(OC main scan) flagUsed to set the main scan magnification ratio in OC scan.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW105 No.2–No.8 Scan magnification ratio adjustment(OC main scan)Used to set the main scan magnification ratio in OC scan.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%SW106 No.1 Scan magnification ratio adjustment(OC sub scan) flagUsed to set the sub scan magnification ratio in OC scan.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW106 No.2–No.8 Scan magnification ratio adjustment(OC sub scan)Used to set the sub scan magnification ratio in OC scan.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%SW107 No.1 Scan magnification ratio adjustment(RSPF back surface main scan) flagUsed to set the main scan magnification ratio in RSPF back surfacescan.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW107 No.2–No.8 Scan magnification ratio adjustment(RSPF back surface main scan)Used to set the main scan magnification ratio in RSPF back surfacescan.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%SW108 No.1 Scan magnification ratio adjustment(RSPF back surface sub scan) flagUsed to set the sub scan magnification ratio in RSPF back surfacescan.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW108 No.2–No.8 Scan magnification ratio adjustment(RSPF back surface sub scan)Used to set the sub scan magnification ratio in RSPF back surfacescan.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%SW109 No.1 Print magnification ratio adjustment(Main scan back surface) flagUsed to set the main scan magnification ratio in back surface print.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW109 No.2–No.8 Print magnification ratio adjustment(Main scan back surface)Used to set the main scan magnification ratio in back surface print.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%SW110 No.1 Print magnification ratio adjustment(Sub scan back surface) flagUsed to set the sub scan magnification ratio in back surface print.Bit 1 indicates plus or minus of the magnification ratio.Default: 0 (+)SW110 No.2–No.8 Print magnification ratio adjustment(Sub scan back surface)Used to set the sub scan magnification ratio in back surface print.By binary input, setting can be made in the range of 0 – ±12.7% in0.1% increments.Default: 0%