Menu
Sealey TS01.V2 Quick Start Manual
  |
700MM VICE/BENCH MOUNTING SHEETMETAL FOLDERMODEL NO: TS01.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 Wear approved safety goggles, gloves, and footwear, when operating the folder. Your local Sealey dealer offers a complete range ofsafety equipment.9 Use the tool only for its intended purpose.9 Regularly check all parts of the folder for damaged parts. DO NOT use if any of its components are broken, worn or damaged.9 Use original Sealey spare parts and accessories. Use of non-recommended spare parts may be dangerous and will invalidatewarranty.9 Ensure good footing, wear non slip footwear.8 DO NOT operate this tool while under the influence of drugs, alcohol or other impairing medication.8 DO NOT Allow unqualified persons to operate the metal folder. Keep children away from the tool.2. INTRODUCTIONBench and vice mounting sheet metal folder, fitted with mounting plates. Capable of bending a 2mm steel sheet, of limited length, up to andbeyond a 90° angle. The unique patented endless design and removable folding plate allows the user to fold, channel and offset any length ofsheet metal up to 1mm thick, by simply moving the sheet as required after each fold. With adjustable fold plate to help achieve the cleanestfold possible. Ideal for the small garage or restoration operation.3. SPECIFICATIONMODEL NO: ............................................................TS01.V2Capacity: .................................. 20 Gauge Sheet, Ø1mm Rod4. OPERATION4.1. Unpack the unit and check that all parts are included and notdamaged. Should you experience a problem contact yoursupplier immediately.4.2. Position folder on bench where it is to be mounted, ensuringthat the handles (fig.1.7) hang vertically over the front of thebench, use foot plates (fig.1.6) as templates to drill holes inbench, use appropriate fixings.Or clamp folder in vice .4.3. By using centre adjustment nut (fig.1.4) ensure top and baseplate are parallel, this may require adjustment from time to time.4.4. Release clamps (fig.1.1) at either end of folder so that as malltest piece of sheet metal can be inserted between the top and base plates. (fig.1.3)4.5. Position the test piece, adjust the top plate by use of clamps (fig.1.1) lightly tighten, use a spanner to adjust cam (fig1.2), so thatbase and top plate are aligned.4.6. Ensure that there is even pressure on both ends.4.7. Raise the top folding plate (fig.1.3) by lifting handles to create the fold. From this test, you will be able to determine how and wherethe fold appears.4.8. When satisfied with the test results, proceed with the actual workpiece.4.9. By rotating the end clamps through the vertical axis, longer lengths of metal sheet can be folded, i.e. fold a section, unclamp, movesheet, reclamp, fold second section etc.1 Top/Base plate clamp2 Adjustment/Positioning Cam3 Removable Folding Plate4 Centre adjustment nut5 Top Plate6 Foot plate with fixing holes7 Folding Handlesfig.1TS01.V2 Issue 1 09/05/2022Original Language Version© Jack Sealey LimitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear safetyfootwear16273 4 5 |
Related manuals for Sealey TS01.V2
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved