Sealey SBS01 Instructions Manual

2. INTRODUCTION4. OpeRaTION3. INsTallaTION1. safeTyHeavy-duty biometric finger print safe. Double safety lockrequires electronic access code or finger print to open thelocking mechanism. Powder coated finish for added corrosionresistance.Original Language Version SBS01, SBS03 Issue: 1 - 31/10/11InStructIonS for:BIOMeTRIC seCURITysafesMoDEL no's: sBs01, sBs03thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.IMPORTANT: please ReaD THese INsTRUCTIONs CaRefUlly. NOTe THe safe OpeRaTIONal ReQUIReMeNTs, WaRNINGs aND CaUTIONs.Use THIs pRODUCT CORReCTly aND ONly fOR ITs INTeNDeD pURpOse. faIlURe TO DO sO May CaUse DaMaGe aND/OR peRsONal INJURyaND WIll INValIDaTe THe WaRRaNTy. ReTaIN THese INsTRUCTIONs fOR fUTURe Use. WaRNING! these safes are heavy and care should beexercised in transit and handling to ensure that no one is injured. for maximum security, these safes must be securely fixed to afloor and/or wall. At all times, these safes should be positioned ona level floor/surface. DO NOT install in areas where damp and condensation arepresent.fig.23.1 Open the safe door using the emergency key as describedin section 4.1.3.2 careful consideration should be given to the sighting of the safeto ensure that it is discreetly placed and not easily found by anyintruders.3.3 Each safe is supplied with four anchor bolts suitable for fixing tobrick and concrete.3.4 fixing to hollow partition walls is not recommended. If fixed towood it must be to a solid wooden structure.3.5 open the door of the safe and with the help of a second person,position it where required and mark the mounting positionsthrough the pre-drilled holes in either the back or the base of thesafe.3.6 Drill four 12mm holes to a depth of 52mm. (fig.2.A)3.7 remove the bolt and washer from each fixing. Ensure thetapered nut is firmly inserted into the split end of each tube andinsert them into the wall, nut first. (fig.2.B)3.8 Position the safe over the four holes and support it there whilsteach bolt is inserted and done up finger tight. (fig.2.c)3.9 continue to support the safe whilst tightening the fixings using a12mm spanner or socket. (fig.2.D)4.1 First time opening of safe. the safe has to be opened the firsttime using the emergency key. the key hole is situated beneatha cover at the bottom of the main panel. See fig.3.4.1.1 Slide the cover downwards and remove it to reveal the keyhole asshown in fig.1a.4.1.2 Insert the emergency key provided as shown in fig.1b and turn itanti-clockwise. turn the silver knob clockwise and open the safe.4.2 Inserting the batteries. the battery compartment is situated onthe back of the safe door. Slide the cover to the left by 12mmand lift it off. Insert four high quality alkaline batteries ensuringthat the polarity is correct according to the markings in the backof the compartment. replace the cover and slide shut.4.2.1 If the red LED to the left of button no.1 illuminates, it meansthat the batteries are low in power and should be replaced.4.3 Changing the preset code. the preset user code is factory setto "1234" and for security purposes should be changed toanother code using the following procedure.4.3.1 Press button no.1 and hold it down for 5 seconds until the greenLED illuminates. release the button and enter the existing code.Press the unlock button to confirm. If correct a beep will sound.fig.1a fig.1b4.3.2 now enter the new code (4 to 8 digits) and press the unlockbutton to confirm. no beep will sound.4.3.3 Enter the new code for a second time and press the unlockbutton to confirm. A beep will sound to confirm that the code hasbeen successfully changed.fig.3seRIal NUMBeR

/ 2

Related manuals for Sealey SBS01