Sealey PT1170H.V2 Manual

Also see for PT1170H.V2: Instructions

Pallet truck 1000kg 1170 x 540mm HigHliftModel no: Pt1170H.V2thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.imPOrtaNt: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. Safety9 only open bottomed euro type pallets can be used with this truck8 DO NOt use a faulty or damaged truck.9 Before using the truck all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the wheels,handle and fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced beforethe truck is used.9 All repairs must be carried out by an authorised Sealey service agent.9 Personnel who operate the truck and those in the vicinity of operation should wear safety footwear with reinforced toe caps at all times.9 never place any part of your body in the lifting mechanism or under the forks or load.8 DO NOt allow others to ride on the truck.8 DO NOt lift or move unstable or loosely stacked loads.9 Take extra care when operating a loaded truck in high winds.9 Take special care when moving long, high or wide loads in order not to dislodge the load by striking any fixtures, vehicles or people inthe area of operation.9 Always ensure that the load is evenly distributed across the forks with the centre of the load being at the halfway point of the length ofthe forks.8 DO NOt overload the truck - refer to the specification for maximum permitted load.9 If a load is left unattended even for a very short period of time it should be lowered to the ground.9 When not in use the truck should be left in the lowered position.9 ensure that the width and length of the forks is correct for the pallet to be lifted.9 ensure that the truck is sufficiently inserted into the pallet to lift the full width of the pallet.9 Use the truck on level, flat, hard surfaces and in well lit areas.8 DO NOt use truck on sloping or uneven ground; DO NOt attempt to negotiate curbs, steps or ramps.9 The operator of the truck must be physically capable of controlling the load selected; particularly in relation to stopping a rolling load.2. iNtrODuctiONHeavy-duty high lift pallet truck suitable for the loading/unloading of light commercial vehicles as well as warehouse/general handling duties.Features twin stabilisers for extra balance when at maximum lift and an ergonomic handle design for comfortable operation.3. SPecificatiONModel no: .......................................................... PT1170H.V2Capacity: .................................................................... 1000kgFork Spread: .............................................................. 225mmForks (length x overall Width): ......................1170 x 540mmMaximum Height: ....................................................... 840mmMinimum Height: .......................................................... 85mmnett Weight: ............................................................ 111.00Kg4. aSSembly4.1. assembling the handle to the truck (fig.1)4.1.1. note that the piston is constrained in the down position by a pin which passes through holes inthe handle mounting bracket (fig.1.B). DO NOt remove this pin yet.4.1.2. Identify and have ready the handle pivot pin (fig.1.A) which will have a roll pin insertedthrough one end of it.4.1.3. Slide the base of the handle into the handle mounting bracket which is an integral part of thepump body and align the holes in the handle with the holes in the bracket (fig.1).4.1.4. drive the pin (fig.1.A) through the aligned holes from left to right using a soft faced hammerand ensure that the roll pin rests in the groove in the bracket (fig.1.d)4.1.5. Move the lever at the top of the handle (fig.2) into the lower position then pass the chain withadjusting bolt and nut through the hole in the centre of the handle pivot pin.4.1.6. lower the handle to depress the piston and remove the restraint pin from the hole ‘B’ abovethe piston (fig.3.B). Place the lever in the central ‘raise’ position.4.1.7. Press and hold down the foot pedal (fig.3.A). Slide the adjusting bolt and nut at the end of thefig.1PT1170H.V2 Issue 3 (HF) 07/02/19Original Language Version© Jack Sealey limitedRefer toinstructionsWear safetyfootwear

/ 3

Related manuals for Sealey PT1170H.V2