Sealey CST801.V2 Manual

FOLDING SACK TRUCK 200KG CAPACITYPNEUMATIC TYRESMODEL NO: CST801.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.CST801.V2 | Issue 1 10/07/2019Original Language Version© Jack Sealey LimitedRefer toinstructionsfig.1fig.2REFERENCE ONLY1. SAFETY9 Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.9 Obtain additional support for large or wide loads to prevent tipping.8 DO NOT overload the truck - see Specification.8 DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.8 DO NOT use truck on uneven ground and do not run over curbs or steps - use a ramp.8 DO NOT allow others to ride on the truck.8 DO NOT use the truck if any part is damaged, paying particular attention to the wheels.2. INTRODUCTIONExtra-strong tubular steel framework with heavy-duty pneumatic tyres allow transport of loadover rough terrain. Features foldaway toe plate and height adjustable handles. Fitted withcomposite grip handles for added comfort and stability.3. SPECIFICATIONModel No: . . . . . . . . . . . . . . . . . . . . . . . . CST801.V2Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200kgHeight(s): . . . . . . . . . . . . . . . . . . . . . . . . 810-1165mmOverall Width: . . . . . . . . . . . . . . . . . . . . . . . . .480mmPlatform Depth: . . . . . . . . . . . . . . . . . . . . . . . .290mmWheel Size: . . . . . . . . . . . . . . . . . . . . . . . . Ø250mmWheel Width: . . . . . . . . . . . . . . . . . . . . . . . . . . .80mm4. ASSEMBLY4.1. WHEELS4.1.1. Ensure each axle is clean from dust and dirt to allow free movement of the wheel.4.1.2. Slide the wheel (fig.1.2) onto the axle (fig.1.1). Place a washer over the axle (fig.1.3).4.1.3. Push the split pin through the hole in the end of the axle and bend over the ends in orderto secure the whole assembly.4.1.4. Repeat for the other side.4.2. TOE PLATE4.2.1. If the toe plate is not already attached, do so using the bolts, washers and nuts supplied.4.2.2. Attach at the bottom of the truck (fig.2.1).5. OPERATION5.1. Check and inflate the tyres. DO NOT inflate above 30psi.5.2. Fold down the toe plate ready to accept a load (fig.2).5.3. The handle can be extended by compressing the tabs on the central bar (fig.2.2) andpulling up on the handle. Pull upwards until a ‘click’ is heard.8 DO NOT overload the sack truck. DO NOT try to carry loads that make the truckunstable.5.4. Slowly lean the sack truck backwards to take the weight of the load.5.5. Proceed at a safe speed especially at corners where there could be a danger of theload shifting.5.6. Extra care should be taken on inclined surfaces.5.7. Where there is a curb or step, a ramp should be used.5.8. After use fold up the toe plate and retract the handles (fig.2.2 & fig.3), store in a safedry place.5.9. Periodically check all fittings are tight. 112

/ 2

Related manuals for Sealey CST801.V2