Sealey AP200.V2 Instructions Manual

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCTCORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILLINVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions and maintained properly, give you years of trouble free performance.Refer to InstructionManual1. SAFETYAP200.V2 Issue: 2 - 03/01/17Original Language Version© Jack Sealey LimitedInStructIonS For:MObILE WORKSTATION - ADJUSTAbLE HEIGHTmodeL no: AP200.V2 WARNING! use workstation on level and solid ground, preferably concrete. Locate workstation in a suitable working area. Keep the work area clean, uncluttered and ensure there is adequate lighting. Keep the workstation clean and tidy in accordance with good workshop practice. Keep children and unauthorised persons away from working area. ensure that fixings have been securely tightened before use. DO NOT use the workstation for any purpose other than that for which it is designed. DO NOT stand on the frame or attempt to ride on it. DO NOT attempt to transport heavy loads on the workstation.2. INTRODUCTIONtable is fully adjustable in height. Features four-section table, one large for main workpiece and three equal sized smaller sections foraccessories. rubber lining on the table helps prevent damage to the unit and workpiece. Suitable for use in workshops and warehouses.Supplied with four castor wheels.Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AP200minimum height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .890mmmaximum height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1190mmtable size (W & d): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .730 x 505mmcapacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25kg3. SPECIFICATION4. ASSEMbLYfig.1Refer to fig.1.4.1. Bolt front wheel frame (10) to joining frame (9). Bolt rear wheelframe (12) to joining frame (9).4.2. Bolt table top base assembly (8) to joining frame (9).4.3. Screw wheels into the bottom of both wheel frames (10) and (12).4.4. Bolt table top mounting frame (6) to table top (3) using springwasher (5) and table top mounting bolt (4). Note: table top(3) and table top mounting frame (6) will only fit together one way.4.5. Insert the table top mounting frame (6) into table top baseassembly (8) so that the table top is centred directly over thelongest width of the wheels, see fig.2.4.6. Screw in table top adjusting screw (7).5. OPERATION WARNING! DO NOT extend the table beyond the extensionwarning line located on the table pole.5.1. to adjust the height of the workstation firstly support the tabletop to prevent it from dropping, then turn the adjusting screw(7) anticlockwise to loosen it.5.2. When positioning the table next to or over painted or 'valuable'surfaces ensure they are covered by protective non-scratchcovers.fig.2

/ 3

Related manuals for Sealey AP200.V2