Sealey AK2946 Instructions Manual

Also see for AK2946: Instructions Quick start guide

Portable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately). Removablesolder tip transforms torch into burning flame heat source. Supplied with a variety of nozzles for various applications including a flameless heatsource adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating, soldering and shrinking.Powered by Butane (lighter fluid).Kit comprises: Butane Solder Torch, Soldering Head with 3 Solder Tips, Spanner for Solder Tips, Curved Deflector Plate, Hot Knife, Spongeand Safety Cap.Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properlymaintained, give years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THISPRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.INSTRUCTIONS FOR:BUTANE SOLDERING/HEATING TORCH KITMODEL No: AK29461. SAFETY INSTRUCTIONS3. OPERATING INSTRUCTIONS WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch. Familiarise yourself with the application and limitations, as well as the potential hazards, peculiar to the torch. Butane gas is highly flammable, so keep an appropriate fire extinguisher close to hand. WARNING! Use and handle the butane gas (lighter fuel) in accordance with the instructions supplied with the fuel. Keep the work area clean, uncluttered and ensure there is adequate ventilation and lighting. Keep children and unauthorised persons away from the working area. Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair. Point the torch away from yourself and others when igniting flame. Keep hands and body clear of the torch head when operating as it becomes very hot. Secure unstable workpiece with a clamp, vice or other adequate holding device. DO NOT get the torch wet. DO NOT use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc. DO NOT use the torch for any purpose other than for which it is designed. DO NOT use accessories other than those supplied with the torch. WARNING! DO NOT touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling it or returning itto its storage case. DO NOT cool the torch in water. DO NOT point the torch at yourself, others, or animals. DO NOT operate the torch when you are tired, or under the influence of alcohol, drugs or intoxicating medication. DO NOT allow untrained persons to operate the torch. DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury. DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool. DO NOT leave the torch, after use, until it has cooled. When work is complete, allow the torch to cool. Clean the torch and accessories, return to case and store in a safe, dry childproof location. DO NOT store in direct sunlight or where the temperature could exceed 104°F/40°C WARNING! Failure to use the torch correctly may result in fire, damage and/or personal injury. DANGER! The flame is invisible in sunlight - be extremely cautious. WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch.Note: The torch is supplied without butane gas. Before use it must be fuelled as follows:3.1. TO FUEL THE TORCH3.1.1. Use only high quality butane gas (lighter fuel) to fill the torch.3.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig.3, ‘Gas On/Off Switch’.3.1.3. Follow the instructions on the butane fuel can.3.1.4. Apply the can filler tip to the torch base filler valve (fig.1). Use a pumping action for best filling results.3.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use.Note: Before refilling, ensure that the filler valve and the probe on the can of lighter fluid are clean and freefrom dirt and debris.Check that the correct filling adaptor is fitted to the lighter fluid refill can.Ensure that the torch and the can of lighter fluid is at roomtemperature before commencing refill.Lighter fluid is highly flammable – refill in a well ventilatedplace, away from any sources of ignition.Fill in conjunction with the operating and safety instructionsfound on the can of lighter fluid.If any spillages occur during the refilling process, allowplenty of time for escaped gas to evaporate beforeallowing sources of ignition in the vicinity.Once full, check the torch for leaks by listening for a hissingnoise. If the hissing persists, do not ignite and remove thetorch to a well ventilated area until the gas has escaped –do not allow any ignition in the vicinity of the tool.fig.12. INTRODUCTIONfig.2Original Language Version AK2946 Issue: 2 - 09/08/11

/ 2

Related manuals for Sealey AK2946