Sealey AK2946 Quick Start Manual

Also see for AK2946: Instructions Instructions

BUTANE HEATING / SOLDERING TORCH KITMODEL NO: AK2946Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETYi WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using thisequipment. WARNING! Always wear approved eye or face protection when operating the torch. WARNING! Butane gas is extremely flammable, handle with care. WARNING! Always point the torch away from the eyes, body or flammable objects when igniting and during operation. WARNING! Ensure the Gas Controller Knob is firmly closed and the flame completely extinguished after use. WARNING! DO NOT puncture the cartridge or dispose of in a fire. Use only specified gas (Sealey Gas Charger Butane SCS035S)8 DO NOT use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard.9 Keep flammable material away from the torch when operating. Flammable waste, such as wiping or cleaning rags, must be placedin a closed metal container and disposed of correctly.8 DO NOT operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.8 DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to secure the workpiece.8 DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or possible personal injury.8 DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.8 DO NOT touch the burner tube during or immediately after use as it will be very hot. Allow to cool.8 DO NOT leave the torch operating unattended.8 DO NOT allow children to operate the torch.9 Disconnect the gas cartridge when not in use. Store cartridge away from direct sunlight in a safe, dry, childproof area, where thetemperature will not exceed 40°C (104°F).9 After use, allow the torch to cool before storing it.IMPORTANT! Observe cautions on the gas refill cartridge label.2. INTRODUCTIONPortable and lightweight torch with piezoelectric start. Features adjustable heating control ranging up to 450°C (approximately).Removable solder tip transforms torch into burning flame heat source. Includes a variety of nozzles for various applications includinga flameless heat source adaptor. Safety cap for storage. Sponge cleaning tray and small roll of solder wire. Suitable for heating,soldering and shrinking. Powered by Butane (lighter fuel). Supplied in storage case.3. SPECIFICATIONModel No.:................................................................ AK2946Sealey Gas Charger Butane .................................. SCS035SContents: Deflector, soldering head, soldering tips (small, medium, large), hot knife, spanner.4. OPERATION WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch.NOTE: The torch is supplied without butane gas. Before use it must be fuelled as follows:4.1. TO FUEL THE TORCH4.1.1. Use only high quality butane gas (lighter fuel) to fill the torch.4.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig.3, ‘Gas On/Off Switch’.4.1.3. Follow the instructions on the butane fuel can.4.1.4. Apply the can filler tip to the torch base filler valve (fig.1). Use a pumping action for best filling results.4.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use.NOTE: Before refilling, ensure that the filler valve and the probe on the can of lighter fluid are clean and free from dirt and debris.Check that the correct filling adaptor is fitted to the lighter fluid refill can.Ensure that the torch and the can of lighter fluid is at room temperature before commencing refill.Lighter fluid is highly flammable – refill in a well ventilated place, away from any sources of ignition.Fill in conjunction with the operating and safety instructions found on the can of lighter fluid.If any spillages occur during the refilling process, allow plenty of time for escaped gas to evaporate before allowing sources of ignition inthe vicinity.AK2946 Issue 3 (H, F) 28/05/19Original Language Version© Jack Sealey LimitedRefer toinstructionmanualWear protectivegloves Wear eyeprotection Warning:hot surfaces

/ 3

Related manuals for Sealey AK2946