Sealey 50LTR V-TWIN Manual

Warning: hotsurfaceWarning: automaticstart-upIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCTCORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILLINVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions and maintained properly, give you years of trouble free performance.Refer to InstructionManualWarning:electricity1. SAFETYCOMPRESSOR 50LTR/100LTR V-TWINDIRECT DRIVE 3HPMODEL NO’S : SAC05030.V2, SAC10030.V21.1. ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets andany other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation ofappropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We alsorecommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that areplugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a ResidualCurrent Device by contacting your Sealey dealer.You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualifiedelectrician, using a Portable Appliance Tester (PAT), at suitable intervals.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliancesand the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.and use a Portable Appliance Tester.1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check allconnections to ensure that none are loose.1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supplyto be used and that the plug is fitted with the correct fuse - see fuse rating at right.1.1.7. DO NOT pull or carry the appliance by the power cable.1.1.8. DO NOT pull the plug from the socket by the cable.1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faultyitem repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug isdamaged, cut the cable just above the plug and dispose of the plug safely.Fit a new plug according to the following instructions (UK only).a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.b)Connect the BROWN live wire to the live terminal ‘L’.c) Connect the BLUE neutral wire to the neutral terminal ‘N’.d) After wiring, check that there are no bare wires, that all wires have been correctly connected,that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensurethat a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socketwith your electrician.1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any applianceplugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that thecapacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the useof 2.5mm² section cable.1.2. GENERAL SAFETY Familiarise yourself with the application and limitations of the compressor. Ensure the compressor is in good condition before use. If in any doubt do not use the unit and contact an electrician/service agent. WARNING! Compressor must only be serviced by an authorised agent. DO NOT tamper with, or attempt to adjust, pressureswitch or safety valve. Before moving or maintaining the compressor ensure it is unplugged from the mains supply, and that the air tank pressure has beenvented. Only use recommended attachments and parts. To use unapproved items may be dangerous and will invalidate your warranty. Read the instructions regarding any accessory used with the compressor. Ensure the safe working pressure of any air appliance usedexceeds unit’s output pressure. Ensure the air supply valve is turned off before disconnecting the air supply hose. To move the compressor use the handle only. SAC05030 only - lift the compressor so that the front feet have enough clearance formanoeuvring, but maintain the unit’s stability. DO NOT attempt to lift or move the compressor by any means other than by the handle. Use the compressor in a well ventilated area with a temperature above 5°C, and ensure it is placed on a firm, level surface.Recommended fuserating: 13ASAC05030.V2, SAC10030.V2 Issue: 2 (L) -15/08/18Original Language Version© Jack Sealey Limited

/ 5

Related manuals for Sealey 100LTR V-TWIN