Samsung iDCS 500 User Instruction

Also see for iDCS 500: User guide User guide User guide Administration guide General description

Contents

45Your keyset may be equipped with a Headset mode key. If it is so equippedpressing this key while the light is out will cause the keyset to enter headsetmode and the light will illuminate to indicate this. Pressing the key while thelight is lit will cause the keyset to return to handset mode and the light willgo out.HOT KEYPADOn your phone system your keyset’s keypad can be made “live” or “hot” sothat it is not necessary to lift the handset or press the SPEAKER key beforeyou begin dialing. Calls can be made and features activated by simply dial-ing the C.O. line number, trunk group access code, intercom number or fea-ture access code. To activate this feature:• With the handset on-hook, press TRANSFER and then dial 110.• Dial 031 to turn the Hot Keypad on or 030 to turn it off.• Press TRANSFER to store your selection.KEY CONFIRMATION TONEYou can hear a short beep (confirmation tone) each time you press a buttonon the dial pad. This tone can be turned on or off.• While on-hook, press TRANSFER and then dial 110.• Dial 040 to turn tones off or 041 to turn tones on.• Press TRANSFER to store your selection.REJOINING A PAGEThis feature allows you to hear the remaining portion of an ongoing internalpage after you return your keyset to idle. To enable this feature:• With the handset on-hook, press TRANSFER and then dial 110.• Dial 051 to turn this feature on or 050 to turn it off.• Press TRANSFER to store your selection.RING PREFERENCEThis feature automatically answers ringing calls when you lift the handset orpress the ANS/RLS key. This method will always answer calls in the orderthey arrived at your keyset. When you turn ring preference off, you mustpress the flashing button to answer a call, allowing you to answer calls in theorder you choose.• With the handset on-hook, press TRANSFER and then dial 110.• Dial 061 to turn ring preference on or 060 to turn it off.• Press TRANSFER to store your selection.CHANGE YOUR PASSCODEFrom the factory, your station passcode is 1234. You can change your sta-tion passcode whenever you desire.• While on-hook, press TRANSFER and then dial 101.• Dial your old passcode.• Dial a new passcode (must be four characters). You can use 0–9.• Redial the new passcode to verify. If successful, you will hear two beeps.Four beeps indicate an incorrect code. Reenter the code again.• Press TRANSFER to store the new passcode.SET ANSWER MODEYou can receive internal calls in one of three modes (see Answering IntercomCalls under Intercom Calls for descriptions):• While on-hook, press TRANSFER and then dial 103.• Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.• Press TRANSFER to store your selection.NOTE: When your keyset is programmed for Auto Answer and you have For-ward No Answer (FNA) turned on, you must answer screened transfers bypressing the ANS/RLS key before your FNA timer expires or the call will for-ward.AUTOMATIC HOLDWhile on an outside call, pressing a line key, route key or a flashing CALLbutton will automatically put your call on hold and connect you to the nextcall. This feature can be turned on or off at your keyset.• With the handset on-hook, press TRANSFER and then dial 110.• Dial 001 to turn Automatic Hold on or 000 to turn it off.• Press TRANSFER to store your selection.NOTE: Intercom calls can be automatically put on hold by pressing TRANS-FER.HEADSET OPERATIONKeyset users can switch between headset mode and handset mode. Whenusing headset mode, press the ANS/RLS key to answer and release calls.• With the handset on-hook, press TRANSFER and then dial 110.• Dial 021 to use the headset or 020 to use the handset.• Press TRANSFER to store your selection.44