Samsung UD46E-A Quick Setup Manual

Also see for UD46E-A: User manual Quick setup guide Quick setup guide

Contents

specifications

Quick Setup GuideThe colour and the appearance may differ depending on the product, and the specifications aresubject to change without prior notice to improve the performance.Download the user manual from the website for further details.http://www.samsung.com/displaysolutionsUD46E-A UD46E-C UD46E-BUD55E-BBN68-07319J-02The terms HDMI and HDMI High-Definition Multimedia Interface, and theHDMI Logo are trademarks or registered trademarks of HDMI LicensingLLC in the United States and other countries.Reverse SideIROUT CONTROL IN DP INHDMI IN 1 HDMI IN 2DVI IN(MAGICINFO) RGB IN USBDP OUT(LOOPOUT)INOUTRS232CINOUTAUDIORJ451 Receives the remote control signal via the external sensor boardand outputs the signal via LOOP OUT.2 Supplies power to the external sensor board or receives the lightsensor signal.3 DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI cable.4 Connects to a source device using an HDMI cable.5 Connects to a PC using a DP cable.6 Connects to a source device using a D-SUB cable.7 Connects to another product using a DP cable.8 Receives sound from a PC via an audio cable.9 Connects to the audio of a source device.0 Connects to MDC using an RS232C adapter.! Connect to a USB memory device. (Only for update purpose)@ Connects to MDC using a LAN cable.Issues SolutionsThe screen keepsswitching on and off.Check the cable connection between the productand PC, and ensure the connection is secure.No Signal is displayedon the screen.Check that the product is connected correctlywith a cable.Check that the device connected to theproduct is powered on.Not Optimum Mode isdisplayed.This message is displayed when a signalfrom the graphics card exceeds the product’smaximum resolution and frequency.Refer to the Standard Signal Mode Table andset the maximum resolution and frequencyaccording to the product specifications.The images on thescreen look distorted. Check the cable connection to the product.The screen is not clear.The screen is blurry.Adjust Coarse and Fine.Remove any accessories (video extensioncable, etc) and try again.Set the resolution and frequency to therecommended level.The screen appearsunstable and shaky. Check that the resolution and frequency of thePC and graphics card are set within a rangecompatible with the product. Then, change thescreen settings if required by referring to theAdditional Information on the product menuand the Standard Signal Mode Table.There are shadows orghost images left on thescreen.The screen is too bright.The screen is too dark. Adjust Brightness and Contrast.Issues SolutionsWhite does not reallylook white.Go to Picture and adjust the White Balancesettings.The product will turn offautomatically.Go to System and make sure Sleep Timer isset to Off.If a PC is connected to the product, check thepower status of the PC.Make sure the power cable is connectedproperly to the product and power outlet.If the signal from a connected device is notdetected, the product automatically turns offafter 10 to 15 minutes.There is no sound. Check the connection of the audio cable oradjust the volume.Check the volume.The volume is too low. Adjust the volume.If the volume is still low after turning it up tothe maximum level, adjust the volume onyour PC sound card or software programme.The remote control doesnot work.Make sure that the batteries are correctly inplace (+/-).Check if the batteries are flat.Check for power failure.Make sure that the power cord is connected.Check for any special lighting or neon signsswitched on in the vicinity.Troubleshooting GuideChecking the Components External sensor KIT108&3 ON1 Aim the remote control towards this spot on the LCD Display.- Keep the area between the remote sensor and remote controlobstacle-free.2 Automatically detects the intensity of ambient light around aselected display and adjusts the screen brightness.3 The power indicator will turn off when the product is turned on.It will blink in power-saving mode.4 Use this button for turning the LCD Display on and off.5 Switches from PC mode to Video mode.Selects the input source that an external device is connected to.- Contact the vendor where you purchased the product if any componentsare missing.- The pictures may look different from the actual components.1234567890!@12345Quick Setup GuideWarranty card(Not available in somelocations)Regulatory guideMagicInfo SoftwareDVD Power cordBatteries(Not available in somelocations)Remote Control DP cable RS232C(IN) adapterAUDIO adapter Holder-Ring (4EA) /Screw (4EA)[UDE-A,B,C-QSG-INDIA]BN68-07319J-02.indd 1 2015-07-02 9:28:00

/ 2

Related manuals for Samsung UD46E-A