Samsung 2004KAISER2 Instruction Manual

ENG-13ENG-12Auto Channel MemoryAuto Channel Memory will automatically seek and storeall active channels in your area.1 Open “MENU”With the DVD in Stop or Play mode, press theMENU button.2 Select “SETUP”Using the UP/DOWN buttons, move the selectionbar to “SETUP” then press ENTER to select.3 Select “Channel”Using the UP/DOWN buttons, move the selectionbar to “Channel”, then press ENTER to select.4 Run “Auto channel memory”Move the selection arrow to “Auto ChannelMemory,” then press ENTER to select.• The DVD-VCR will automatically search for allavailable channels in the selected Tuner Band.This procedure may take a few minutes tocomplete.• When finished, the lowest channel found will bedisplayed.Ant./Cable : AntennaRF Output CH : 3CHAuto Channel MemoryChannel Add/DeleteLanguage : EnglishFront Display : AutoAuto Power Off : OffTuner Band Setting RF Output ChannelThis feature allows you to manually set the DVD-VCR’stuner band to Antenna or Cable, whichever youconnected to the Antenna In jack during initial setup.• Use this setting only if Auto Setup detected theincorrect tuner band, i.e. channels are coming in onthe wrong channel numbers.1 Open “MENU”With the DVD in Stop or Play mode, press theMENU button.2 Select “SETUP”Using the UP/DOWN buttons, move the selectionbar to “SETUP” then press ENTER to select.3 Select “Channel”Using the UP/DOWN buttons, move the selectionbar to “Channel”, then press ENTER to select.4 Select “Ant./Cable”Move the selection arrow to “Ant./Cable” then pressRIGHT button to select from the following options:• Antenna - Indicates that the DVD-VCR isconnected to an indoor or outdoor VHF/UHFantenna.• Cable TV - Indicates that the DVD-VCR isconnected to Cable TV.1 Open “MENU”With the DVD in Stop or Play mode, press theMENU button.2 Select “SETUP”Using the UP/DOWN buttons, move the selectionbar to “Setup” then press ENTER to select.3 Select “Channel”Using the UP/DOWN buttons, move the selectionbar to “Channel,” then press ENTER to select.4 Select “RF Output CH”Move the selection bar to “RF Output CH”, thenpress right to change.5 Change “RF Output CH”A message will appear on your TV.Then press ENTER to change.6 Change “TV Channel”A message will appear on your TV. When themessage disappears, change your TV to channel 3or 4 to match the RF output channel of the player.Language : EnglishFront Display : AutoAuto Power Off : OffAnt./Cable : AntennaRF Output CH : 3CHAuto Channel MemoryChannel Add/DeleteCable TVAntennaLanguage : EnglishFront Display : AutoAuto Power Off : OffAnt./Cable : AntennaRF Output CH : 4CHAuto Channel MemoryChannel Add/Delete3CH4CHacxzChannel Add/DeleteUse this feature if Auto Channel Search missed achannel that you would like to add, delete a channelyou wish to remove.1 Open “MENU”With the DVD in Stop or Play mode, press theMENU button.2 Select “SETUP”Using the UP/DOWN buttons, move the selectionbar to “SETUP” then press ENTER to select.3 Select “Channel”Using the UP/DOWN buttons, move the selectionbar to “Channel”, then press ENTER to select.4 Select “Channel Add/Delete”Move the selection bar to “Channel Add/Delete,”then press ENTER to select.5 Select Channel to Add/DeleteUse the CH / buttons to tune in the channelnumber you wish to add or delete.6 Select “Channel Add/Delete”Press RIGHT button to add or press left button todelete the channel from your channel list.• Repeat steps 4 and 5 to add or delete additionalchannels.Ant./Cable : AntennaRF Output CH : 3CHAuto Channel MemoryChannel Add/DeleteCHANNEL ADD/DELETESelect channel : [02]and press [❿] to ADDpress [➛] to DELETERETURN CH ❷Language : EnglishFront Display : AutoAuto Power Off : Off