Samsung 2004KAISER2 Instruction Manual

ENG-7Basic Connections/Auto SetupENG-6Insert Batteries into RemoteFront Panel Display• Remove the battery cover on the remote• Insert two 1.5V “AAA” batteries as shown,making sure of the correct polarities(+/-)• Slide the cover back onto remote.4 51 2 31 When the light is on, DVD is operating.2 The time, counter position, time remaining orcurrent deck status is indicated.3 VCR is activated.4 DVD or CD media is loaded.5 VHS videotape is loaded.S-Video/Component VideoConnections (for DVD)Use the S-Video or Component Video connectionmethod only for the DVD player. The VCR can still beviewed through line input mode on your TV.To activate your alternative (S-Video or Component)video selection, follow the “Alt Video Out” instructionson page 19. Keep in mind that you can choose eitherS-Video or Component only, but not both. A superiorvideo quality can be obtained when watching a DVDon your DVD-VCR if your TV is equipped with S-Videoor Component Video inputs.1 Connect S-Video Out to TVUsing an S-Video cable, connect the S-VIDEO OUTon the rear panel of your DVD-VCR to the S-VideoInput on your TV.2 Connect Component Video Out to TVUsing a component video cable, connect theCOMPONENT VIDEO OUT (Y, Pb, Pr) on the rearpanel of your DVD-VCR to the Component VideoInput on your TV. .3 Connect Audio Out (DVD only)Using RCA audio cables, connect the LEFT/RIGHTLine Out jacks on the rear panel of your DVD-VCRto the LEFT/RIGHT Audio Line In jacks on your TV.• When connecting your DVD-VCR to a TV with theS-Video or Component Video Output, make surethat you use these Line Out jacks.• To activate your connection, see “Alt Video Out”on page 19.To S-Video Input on Your TVTo Component Video Inputon Your TVTo Left/Right Audio Inputson Your TVStereo ConnectionsYou can connect your DVD-VCR to your home stereosystem or stereo TV and enjoy stereo sound whenwatching a movie or TV.1 Connect DVD-VCR to StereoUsing RCA cables, connect the Line Out Left andRight Audio jacks on the rear panel of the DVD-VCRto the Auxiliary Inputs on your stereo receiver.Connect the Video Output also in case you are usinga stereo TV.2 Set Stereo to Auxiliary ModeSet your stereo receiver or TV to either “Aux” or“Tape” regardless of which line input you are using foryour particular device.3 Play a TapeInsert a DVD or Hi-Fi stereo videotape into yoursystem. Be sure to adjust the volume on your stereoreceiver or TV. Audio will be heard through yourstereo speakers• If there is no stereo sound even after you haveinserted a Hi-Fi stereo videotape, press the AUDIObutton until “Hi-Fi” appears on the on-screen display.4 Turn On your DVD-VCRTurn on the power by pressing the POWER buttonon the remote control or on the front panel of theunit.5 Turn On your TVTurn on the TV by pressing the POWER button onthe TV remote control.6 Set the TV to LineSet your TV to its Line Input.You will need to connect the DVD-VCR to a TV and runAuto Setup. The Auto Setup will automatically search forchannels and then set your DVD-VCR's internal clock.NOTES:• See page 7 for Advanced Connections.• Standard RF or Line connection between your TVand DVD-VCR are required to run DVD-VCRsetup menu, even if you connect S-Video orComponent Video Output for a better picturequality.1 Connect the RF Antenna Cable to your DVD-VCRConnect an external indoor/outdoor antenna or walloutlet antenna cable to the Ant-In jack on the rearpanel.32 Connect your DVD-VCR to a TVRF ConnectionUsing the RF antenna cable➁, connect the OUTjack (TO TV) on the rear panel of your DVD-VCR toyour TV’s Antenna Input.Line ConnectionUsing an RCA-type audio/video cable➂ (red, white,yellow), connect the LINE OUT jacks on the rearpanel of your DVD-VCR to your TV's Line In jacks.Use the three cables as follows: red for right audio,white for left audio, and yellow for video.Note: If your TV is equipped with RCA jacks, it isbetter to use the Line Connection method.3 Plug InYour DVD-VCR's power should be plugged into astandard 120V/60Hz wall outlet. Avoid pressing anybuttons on the remote control or on the unit duringan Auto Setup. While your DVD-VCR is running anAuto Setup, “AUTO” will blink. When Auto Setup iscomplete, the current time will be displayed on thefront panel displayed. In case Auto Clock set fails tolocate a channel to set the clock, you should setthe clock manually. See page 11.LINE INPUTPROGRESSIVE SCAN NOTICEConsumers should note that not all high definitiontelevision sets are fully compatible with this productand may cause artifacts to be desplayed in thepicture. In case of 525 progressive scan pictureproblems, it is recommended that the user switchthe connection to the “standard definition”output. Ifthere are questions regarding our TV setcompatibility with this model 525p DVD player.please contact our customer center.